Results 81 to 90 of about 98,877 (294)
Atomically Thin Sieves: Two‐Dimensional Materials for Membrane Separation
Advanced Physics Research, EarlyView.Atomically thin membranes derived from 2D materials overcome the inherent selectivity‐permeability trade‐off in conventional separation technologies. This perspective elucidates transport mechanisms for gases, water, and ions, surveys fabrication strategies including top‐down pore engineering and bottom‐up synthesis, highlights recent experimental and ...
Yiran Gong, Pengzhan Sun, Yu Ji
wiley +1 more source
Mechanical and Magnetic Properties of Cold Rolled 0.02C-6.56Si High Silicon Steel Sheet
Teshugang, 2007 The manufacture process of sheet of high silicon steel 0.02C,6.56Si,0. 14Mn,0.013P,0.004S, 0.02Al was melting by 25 kg vacuum induction furnace, forging breakdown,hot rolling to 1mm at 1050～850 ℃,warm rolling to 0.3 mm at 650℃,and cold
刘艳 +4 more
doaj
EBSD study of microstructure evolution of ferritic stainless steel during cold rolling and annealing
MATEC Web of Conferences, 2018 The microstructure and texture of ferritic stainless steels (FSSs), formed during cold rolling and annealing processes, determine the mechanical properties of final sheet, especially the deep drawing formability. In this work, aNb, Ti stabilized17%Cr FSS
Zhang Chi +3 more
doaj +1 more source
Development and characterization of Powder Metallurgy (PM) 2XXX series Al alloy products and Metal Matrix Composite (MMC) 2XXX Al/SiC materials for high temperature aircraft structural applications [PDF]
The results of a series of material studies performed by the Lockheed Aeronautical Systems Company over the time period from 1980 to 1991 are discussed. The technical objective of these evaluations was to develop and characterize advanced aluminum alloy ...
Chellman, D. J. +2 more
core +1 more source
The Anatomical Record, EarlyView.Abstract The anatomical description of the hourglass dolphin (Cephalorhynchus cruciger) and the spectacled porpoise (Phocoena dioptrica) remains largely unexplored, due to limited specimen availability and preservation challenges. This study employed digital imaging techniques, conventional histology, and computed tomography to provide visualization of
Jean‐Marie Graïc +26 more
wiley +1 more source
Effect of Annealing Processing on Structure and Properties of Ferritic Stainless Steel 00Cr12Ti
Teshugang, 2008 Efiect of annealing at 700～900 ℃ on structure and mechanical properties of 00Cr12Ti steel 1 mm sheet produced by 25 kg vacuum induction funace melting,7 passes hot rolling to 3 mm plate and cold rolling process has been studied.
李烁 +4 more
doaj
Oxide dispersion strengthened nickel produced by nonreactive milling [PDF]
It is shown that oxide dispersion strengthened alloys can be produced by a postulated nonreactive milling mechanism whereby the dispersoid is trapped at the interface between welding metal powder particles. This interparticle welding is possible because,
Arias, A.
core +1 more source
Deep Underground Science and Engineering, EarlyView.Aluminum‐enhanced afterburning renders AE explosives more hazardous than conventional ones. Corrugated steel linings reduce far‐field AE blast overpressure by ~50% through wave reflection and dissipation. The developed model accurately predicts peak pressure (<10% error) and arrival time (<3% error), supporting protective design.
Zhen Wang +5 more
wiley +1 more source
Teshugang, 2013 The influence of cold rolling reduction (65% ~ 80% ) of 3. 13 mm hot rolled plate and recrystallization annealing temperature (660 ~ 780 °C ) on texture and formability-train-hardening exponent (n) and plastic stain ratio (r) of 0.64~1. 10 mm cold rolled
罗海燕 +6 more
doaj
A process model for air bending [PDF]
, 1996 A so called `three-section¿ model for air bending is presented. It is assumed that a state of plane strain exists and that Bernoulli's law is valid.
de Vin, L.J. +4 more
core +3 more sources