Results 41 to 50 of about 349,833 (258)
Study on Strength and Behaviour of Cold-Formed Steel Built-up Columns [PDF]
, 2021 K. Sivasathya +3 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann +4 more
wiley +1 more source
Penggunaan Washer Khusus (Besar) Pada Sambungan Baja Cold-Formed [PDF]
, 2008 . Bolt Connection Design for cold-formed steel could not use friction mechanism (AISI 2001). On other side, bearing mechanism which is based on bolt diameter and plate thickness indicates inefficiency of bolt USAge because of the minimum size of cold ...
Dewobroto, W. (Wiryanto) +1 more
core
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
Advanced Engineering Materials, EarlyView.The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Pre-Stress Linear and Nonlinear Buckling of Cold-Formed Steel Built-up Box Studs
, 2023 Thu Ya Mon, Janani Selvam
openalex +2 more sources
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source