Results 71 to 80 of about 244,474 (303)
Cold spray technology: future of coating deposition processes [PDF]
Cold spray (CS) belongs to a wide family of thermal spray technology with the difference that it is a solid state process in which spray particles are deposited via supersonic velocity impact at a temperature much below the melting point of the spray ...
Kalsi, S.B.S. +2 more
core +1 more source
Decoding NASICON and Its Metal Interface for Solid‐State Batteries
Advanced Materials, EarlyView.This review paper focuses on lithium‐ and sodium‐based NASICON solid electrolytes and their interfaces with metal anodes using a top‐down framework. It begins with NASICON fundamentals, elucidates anode‐induced failure mechanisms, surveys advanced characterization strategies to understand them, summarizes mitigation approaches, and concludes with a ...
Jiaqi Xu +8 more
wiley +1 more source
Experimental Investigation of Fuel Film Characteristics after Spray Impacting on Ultra-cold Surface [PDF]
Journal of Applied Fluid MechanicsIn extremely cold environments, the phenomenon of spray impacting on surfaces is unavoidable and the fuel film attached to the surface is one of the crucial factors influencing emission, stability, and cold-start performance in internal combustion ...
S. Jin +5 more
doaj +1 more source
Designing strategies to control grey mould in strawberry cultivation using decision support systems [PDF]
, 2009 Grey mould is one of the major diseases in strawberry cultivation. Fungicides to control Botrytis cinerea are applied frequently during flowering and sometimes at harvest.
Evenhuis, A., Wilms, J.A.M.
core +2 more sources
Toward a Consensus Characterization Protocol for Organic Thermoelectrics
Advanced Materials, EarlyView.We advocate a common consensus on accurate and standardized reporting of performance metrics in the field of organic thermoelectrics. We summarize prevalent issues in the literature and propose a pre‐submission checklist to support the publication of reproducible results.
Bernhard Dörling +14 more
wiley +1 more source
Beyond Earth: Resilience of Quasi‐2D Perovskite Solar Cells in Space
Advanced Materials, EarlyView.In the article (DOI: 10.1002/adma.202520433), Christoph Putz and co‐workers demonstrate rigid quasi‐2D perovskite solar cells operating in low Earth orbit, delivering stable power for more than 100 days under real‐space conditions. In‐orbit performance is correlated with extensive ground‐based thermal and proton‐irradiation studies on rigid and ...
Christoph Putz +17 more
wiley +1 more source
Photocatalytic Water Splitting on the Lunar Surface: Prospects for In Situ Resource Utilization
Advanced Materials Interfaces, EarlyView.Water has been found in craters on the moon nearby locations which are illuminated >80% of the time. Photocatalysis uses energy from sunlight to drive chemical reactions such as water splitting to produce oxygen and hydrogen. It is a scalable technology that requires lighter equipment and utilizes resources available on the moon. ABSTRACT The discovery
Ranjani Kalyan +6 more
wiley +1 more source
Increase of cold tolerance in cotton plant (Gossypium hirsutum L.) by mepiquat chloride [PDF]
Three mepiquat chloride (MC) concentrations - 40, 70, and 100 g a.i./ha - were used to spray cotton (Gossypium hirsutum L., cultival McNair 220) plants to determine whether or not MC would increase their cold tolerance. Seven to ten days after the spray,
Escobar, D. E. +4 more
core +1 more source
Advanced Materials Technologies, EarlyView.Recent research on laser‐processed cermets and cemented carbides highlights significant advancements, yet a notable paucity of studies and persistent challenges remain. Efforts are increasingly focused on developing low‐cost, environmentally friendly cermets as alternatives to conventional materials.
Himanshu Singh Maurya +2 more
wiley +1 more source