Results 51 to 60 of about 17,986 (306)

Towards Fully Additively-Manufactured Permanent Magnet Synchronous Machines: Opportunities and Challenges [PDF]

, 2019
With the growing interest in electrification and as hybrid and pure electric powertrains are adopted in more applications, electrical machine design is facing challenges in terms of meeting very demanding performance metrics for example high specific ...
EL-Refaie, Ayman M., Wu, Fan
core   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Production of syndiotactic polystyrene powder for part manufacturing through SLS [PDF]

, 2014
Selective laser sintering (SLS) is a well-established additive manufacturing (AM) process. While AM originally found its use as rapid prototyping technique, it is nowadays more and more considered for the production of actual end-use parts.
Cardon, Ludwig, Haverans, Tom, Mys, Nicolas, Verberckmoes, An   +3 more
core  

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source

Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Cold spray-friction stir hybrid additive manufacturing of 316L SS: Feasibility, microstructure, and mechanical performance

Materials & Design
Cold spray additive manufacturing of strain hardenable austenitic steels often yields poor properties in the as-fabricated state. The cold spray-friction stir additive manufacturing (CFAM) process, which combines cold spray (CS) deposition with friction ...
Srinivasan Nagarajan, Michael Carter, Todd Curtis, Grant Crawford   +3 more
doaj   +1 more source

Quantitative percussion diagnostics for evaluating porosity and surface roughness of cold sprayed and laser deposited materials

Journal of Materials Research and Technology, 2021
Quantitative percussion diagnostics (QPD) is a non-destructive evaluation method that has been used successfully in a number of applications. This technique involves a rod that is actuated to impact a specimen with a given amount of kinetic energy and ...
Mahsa Amiri, Grant A. Crawford, James C. Earthman   +2 more
doaj   +1 more source

Near net shape manufacturing of metal : a review of approaches and their evolutions [PDF]

, 2017
In the last thirty years the concept of manufacturability has been applied to many different processes in numerous industries. This has resulted in the emergence of several different "Design for Manufacturing" methodologies which have in common the aim ...
Corney, Jonathan R, Cunningham, David, Marini, Daniele   +2 more
core   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

Advanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin, Marvin Erck, Kevin Jasutyn, Katja Radermacher, Andreas Bund, Mario Kurniawan   +5 more
wiley   +1 more source