Results 51 to 60 of about 120 (100)

Graphite Nodularity Evaluation in High-Si Ductile Cast Irons. [PDF]

Materials (Basel), 2022
Riposan I, Anca D, Stan I, Chisamera M, Stan S.   +4 more
europepmc   +1 more source

Impact of cutting forces on surface quality in finish face milling of compacted graphite iron with CBN and nitride ceramic tools

Технічна інженерія
The article presents the results of studies to determine the influence of cutting forces on the quality parameters of machined surfaces as a result of finishing face milling of products made of compacted graphite cast iron (CGI) using round cutting ...
S.I. Radkevych
doaj   +1 more source

Cast iron - a predictable material [PDF]

China Foundry, 2011
High strength compacted graphite iron (CGI) or alloyed cast iron components are substituting previously used non-ferrous castings in automotive power train applications.
Jorg C. Sturm, Guido Busch
doaj  

Wear resistance of cutting inserts made of cubic boron nitride and ceramic during face milling of compacted graphite iron

Технічна інженерія
Compacted graphite irons increasingly being used in mechanical engineering due to the successful combination of mechanical properties of gray and high-strength cast irons, including high strength, ductility, thermal conductivity and the ability to dampen
V.M. Ruban
doaj   +1 more source

Coating-thickness-dependent physical properties and cutting temperature for cutting Inconel 718 with TiAlN coated tools. [PDF]

J Adv Res, 2022
Zhao J, Liu Z, Ren X, Wang B, Cai Y, Song Q, Wan Y.   +6 more
europepmc   +1 more source

Optimization of cutting parameters in machining of Compacted Graphite Iron (CGI)

, 2011
Compacted Graphite Iron offers mechanical properties in between of gray cast iron and ductile iron. Thus,the material is seen as a hopeful alternative for engine cylinder blocks and heads satisfying environmentaland performance objectives. Nevertheless, CGI is more difficult to machine than conventional gray castiron due to the presence of MnS and thin
openaire   +1 more source

Study of Wear, Stress and Vibration Characteristics of Silicon Carbide Tool Inserts and Nano Multi-Layered Titanium Nitride-Coated Cutting Tool Inserts in Turning of SS304 Steels. [PDF]

Materials (Basel), 2022
Ganeshkumar S, Singh BK, Kumar SD, Gokulkumar S, Sharma S, Mausam K, Li C, Zhang Y, Tag Eldin EM.   +8 more
europepmc   +1 more source

Effect of Cutting Fluid on Milled Surface Quality and Tool Life of Aluminum Alloy. [PDF]

Materials (Basel), 2023
Pang S, Zhao W, Qiu T, Liu W, Yan P, Jiao L, Wang X.   +6 more
europepmc   +1 more source

Performance of tool with hard coating when cutting compacted cast iron under different spray filed

Jin'gangshi yu moliao moju gongcheng, 2019
The spraying field and cutting performance of oils on water (OoW) in the machining of compacted graphite iron (CGI) using cutting tools with hard coatings has been investigated in this paper.
LIN Haisheng, WANG Chengyong, LUO Jie, LAI Zhiwei, YANG Jianzhang, ZHENG Lijuan   +5 more
doaj  

Effect of the Adaptive Response on the Wear Behavior of PVD and CVD Coated Cutting Tools during Machining with Built Up Edge Formation. [PDF]

Nanomaterials (Basel), 2020
Fox-Rabinovich G, Gershman IS, Yamamoto K, Dosbaeva J, Veldhuis S.   +4 more
europepmc   +1 more source