Results 171 to 180 of about 87,932 (314)

Soft Mechanical‐Electrical Logic Using Liquid Metal‐Filled 3D‐Printed Architectures

Advanced Engineering Materials, EarlyView.
We present 3D‐printed soft mechanical–electrical logic elements that use liquid metal–filled silicone tubes actuated by thermoplastic polyurethane/polylactic acid (TPU/PLA) architectures to produce Boolean operations. Complementary normally open and normally closed unit cells perform repeatable binary transitions and can be combined into more complex ...
Christoph Lehmann, Ryan Kalgreen, Laura M. Comella   +2 more
wiley   +1 more source

Guiding gaze via gaze: Effect anticipation during intentional saccadic gaze leading. [PDF]

Psychol Res
Landmann E, Weller L, Riechelmann E, Kunde W, Huestegge L.   +4 more
europepmc   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

How agency shapes behavior and performance: the triple impact of control-feedback on stimulus-response learning, motor reinforcement, and motivated action selection. [PDF]

Front Psychol
Karsh N.
europepmc   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

Experimental Evaluation of Kinematic Compatibility in Three Upper Limb Exoskeleton Configurations Using Interface Force and Torque. [PDF]

Biomimetics (Basel)
Zeng H, Liu H, Fu L, Cao Q.
europepmc   +1 more source

Encyclopedia of 2D β′‐In2Se3 Growth Using Chemical Vapor Deposition: The Effects of Synthesis Parameters Onto Material Quality

Advanced Engineering Materials, EarlyView.
A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge, P. Sanju S. Panawala, Joseph F. S. Fernando, Zhenhuan Chen, Chao Zhang, Dong‐Chen Qi, Liangzhi Kou, Konstantin L. Firestein, Dmitri V. Golberg   +8 more
wiley   +1 more source

Modeling Factors Affecting Physicians' Acceptance of E-Prescriptions Using Structural Equation Modeling-Partial Least Squares Analysis: A Cross-Sectional Study. [PDF]

Health Sci Rep
Zahiri M, Yazdani A, Honarvar B, Rezaee R, Erfannia L.   +4 more
europepmc   +1 more source

Editoral: Advancements in power system condition monitoring, fault diagnosis and environmental compatibility

Frontiers in Energy Research
Feng Liu, Weicheng Yu, Jun Chen, Hui Wan, Shuai Yao   +4 more
doaj   +1 more source

On the compatibility conditions of finite deformations

This paper examines the intuitive meaning of the Saint--Venant compatibility equation known from the linear theory of deformations. The linearized theory is typically obtained from the relations of finite deformation theory by neglecting higher-order terms.
openaire   +2 more sources