Results 131 to 140 of about 6,529 (264)

Effect of Thickness and Stitch Density on Low-Velocity Impact and Compression After Impact Properties of Stitched Composite Laminates. [PDF]

Polymers (Basel)
Liu B, Wang F, Zheng Y, Huang J, Jiang S, Zhang W.   +5 more
europepmc   +1 more source

Experimental and Numerical Study of Healing Effect on Delamination Defect in Infusible Thermoplastic Composite Laminates. [PDF]

Materials (Basel), 2023
Griskevicius P, Spakauskas K, Mahato S, Grigaliunas V, Raisutis R, Eidukynas D, Perkowski DM, Vilkauskas A.   +7 more
europepmc   +1 more source

Additive‐Manufactured, Multifunctional Bioreactor Technology for Dynamic Culture of 3D Bioprinted Tissue Models

Advanced Materials Technologies, EarlyView.
We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger, Johann Schorzmann, Hsuan‐Heng Lu, Muhammad Osama, Julian Bauer, Michael Haug, Oliver Friedrich, Aldo R. Boccaccini, Frank Döpper, Sahar Salehi   +9 more
wiley   +1 more source

Repeated Low-Velocity Impact Properties of Hybrid Woven Composite Laminates. [PDF]

Materials (Basel)
Mutsuddy S, Cai D, Hossain MH, Wang X.
europepmc   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

Multistage Static and Dynamic Optimization Framework for Composite Laminates in Lightweight Urban Rail Vehicle Car Bodies. [PDF]

Materials (Basel)
Cascino A, Distaso F, Meli E, Rindi A.
europepmc   +1 more source

Flexible Pressure Sensor With Co‐Optimized Sensitivity and Linearity Based on Gradient Toroidal Microstructures

Advanced Materials Technologies, EarlyView.
A flexible piezoresistive pressure sensor with gradient toroidal CNT/PDMS microstructures is reported. The hierarchical geometry enables sequential electrode contact, achieving a sensitivity of 256.20 kPa−1 and linear response (R2 = 0.99) over 0–1000 kPa.
Rongmei Wang, Ruolin Liu, Ming Lei, Yifan Liu, Fengming Hu, Bing Ji, Chao Peng, Jianyi Luo, Bingpu Zhou   +8 more
wiley   +1 more source

Enhanced Fracture Energy and Toughness of UV-Curable Resin Using Flax Fiber Composite Laminates. [PDF]

Biomimetics (Basel)
Ou M, Li H, Tan D, Peng Y, Zhong H, Wu L, Shan W.   +6 more
europepmc   +1 more source

A Review of Electrospun Nanofiber Interleaves for Interlaminar Toughening of Composite Laminates. [PDF]

Polymers (Basel), 2023
Mahato B, Lomov SV, Shiverskii A, Owais M, Abaimov SG.   +4 more
europepmc   +1 more source

Fully Printed Electrocaloric Heat Pump

Advanced Materials Technologies, EarlyView.
A system based on a flexible printed PEDOT:PSS/P(VDF‐TrFE‐CFE) electrocaloric membrane. The membrane periodically alternates between the cold and hot sides following its electrocaloric cycle and successfully generates a temperature difference. The entire fabrication process is industrially scalable, cost‐effective, and based on widely accessible ...
Adrian Agreda, Florian Le Goupil, Guillaume Payrot, Sokha Khiev, Jean‐David Isasa, Wiljan Smaal, Guillaume Fleury, Georges Hadziioannou   +7 more
wiley   +1 more source