Results 231 to 240 of about 1,931,160 (313)

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Multiple Lumbar Compression Fractures Following a New-Onset Seizure: A Case Report. [PDF]

Cureus
Wang R, Votapek S, Okun JF.
europepmc   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Tensile properties of sheet-based triply periodic minimal surface lattices fabricated using vat polymerization. [PDF]

Sci Rep
Baghous N, Abraham MA, Mogos NT, Al-Rub RKA.   +3 more
europepmc   +1 more source

Adaptive Dynamic Range Compression Method for Panchromatic Images Based on Detail Regions Gradient Preservation [PDF]

Peng Zhang, Qiang Xu, Yuwei Zhai, Tao Guo, Jiale Wang, Jinlong Xie   +5 more
openalex   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Intraneural Ganglion of the Suprascapular Nerve with Asymmetric Branch Recovery and Dual-Site Compression: A Case Report. [PDF]

J Orthop Case Rep
Keppens M, Thielman L, Biebauw S, Muermans S.   +3 more
europepmc   +1 more source

Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings

Advanced Engineering Materials, EarlyView.
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, Claudio Shyinti Kiminami, Walter José Botta, Claudemiro Bolfarini, Guilherme Yuuki Koga   +8 more
wiley   +1 more source

Elastic-Plastic Deformation Analysis of Cantilever Beams with Tension-Compression Asymmetry of Materials. [PDF]

Materials (Basel)
He XT, Yin JM, Chen ZP, Sun JY.
europepmc   +1 more source