Results 261 to 270 of about 2,560,432 (345)

3D‐Printed Architected Material for the Generation of Foam‐Based Protective Equipment

Advanced Engineering Materials, EarlyView.
This study investigates 3D‐printed architected structures as alternatives to traditional foams in protective gear. It focuses on customizing impact strength and damping through design and manufacturing integration. Testing shows these structures outperform conventional foams, offering enhanced customizability, lower weight, and tunable performance ...
Ali Zolfagharian, Gerard Bel Català, Daniel Saakes, Bernard Rolfe, Ian Gibson, Mehrshad Mehrpouya   +5 more
wiley   +1 more source

Tokenized and continuous embedding compressions of protein sequence and structure. [PDF]

Patterns (N Y)
Lu AX, Yan W, Yang KK, Gligorijevic V, Cho K, Abbeel P, Bonneau R, Frey NC.   +7 more
europepmc   +1 more source

Influence of Temperature on Scratch and Wear Properties of Technical Thermoplastics: Implications for Material Selection

Advanced Engineering Materials, EarlyView.
The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram, Thomas Koch, Vasiliki-Maria Archodoulaki   +2 more
wiley   +1 more source

Elevated Contact Stresses Compromise Activity-Mediated Cartilage Rehydration but not Lubrication. [PDF]

Ann Biomed Eng
Akanda SR, Kupratis ME, Bhattacharjee A, Benson J, Burris DL, Price C.   +5 more
europepmc   +1 more source

Effect of Thermomechanical Processing on the Impact Deformation of Additively Manufactured 316L Stainless Steel

Advanced Engineering Materials, EarlyView.
Previous studies on additive manufacturing primarily focus on the mechanical properties of as‐printed components. In the present work, researchers explore the potential of employing novel thermomechanical postprocessing techniques to improve the microstructure after printing.
Radim Kocich, Lenka Kunčická, Zifan Wang, Gergely Németh   +3 more
wiley   +1 more source

Functional Compression of the Right Internal Carotid Artery by the Hyoid Bone in a Patient with Moyamoya Syndrome and Low Internal Carotid Artery Bifurcation: A Case Report. [PDF]

Vasc Health Risk Manag
Bicevska K, Skrastina S, Kupcs K, Raita A, Balodis A.   +4 more
europepmc   +1 more source

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Biofluid Mechanics and Pathology of Venous Compression Syndromes: A Scoping Review. [PDF]

Cureus
Rivera K, Ahn SS.
europepmc   +1 more source

LONG RANGE AND SHORT RANGE FRICTIONAL SLIP-LINES ON PLANE CONTACT SURFACE IN PLASTIC COMPRESSION (THE RULE OF ISOCLINIC GRADIENT)

, 1958
LIU SHU-I
openalex   +1 more source

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source