Results 91 to 100 of about 149,057 (262)

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

A polymorphic cooperative compression strategy for IoT time series data based on NVM

大数据
The compression strategy plays an important role in the performance of IoT time series data storage system.However, the current compression strategies can not adapt to the characteristics of NVM and IoT time series data.This paper proposes a polymorphic ...
Tao CAI, Tianle LEI, Dejiao NIU, Jianfei DAI, Zeyu HUANG, Qiangqiang NI   +5 more
doaj  

Non-linear Large Deformation Analysis on Packer Rubber in Thermal Production Wells

Shiyou jixie, 2016
The sealing performance of the packer rubber in complex downhole conditions is one of the key points affecting the production safety of thermal production wells.
Fu Daoming
doaj  

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source