Results 161 to 170 of about 206,979 (310)

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Effect of cerium oxide nanocatalyst on performance emissions and noise of diesel biodiesel blends in a variable compression ratio engine. [PDF]

Sci Rep
Anish M, Majid M, Thentral TMT, Raaza A, Kumar A, Deepak JR, Kanan M, Sathish T, Jayaprabakar J.   +8 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

FPGA-accelerated streaming data reduction achieving an average compression ratio over 8000 in a 17.4 kHz, 840 kpixel CITIUS detector for quasi-elastic gamma-ray scattering. [PDF]

J Synchrotron Radiat
Nishino H, Kobayashi M, Hiraki TN, Honjo Y, Ozaki K, Yamaga M, Nagasawa N, Yoda Y, Joti Y, Saito M, Hatsui T.   +10 more
europepmc   +1 more source

Analysis on Emissions of Gasoline Engine with Different Ethanol Blends at Different Compression Ratio

, 2022
Tarun Solanki, Shashi Jain, Ankit Goyal
openalex   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Optimization of compression ratio in LHR engine fueled with nano Al₂O₃-emulsified biodiesel using RSM and machine learning. [PDF]

RSC Adv
Gopidesi RK, Uttamrao KN, Naik N CK, S R P, Hadi AA, Kumar KS, Khan TMY, Shaik AS, Alamiery AA.   +8 more
europepmc   +1 more source

Compression Ratio Effects on Performance, Efficiency, Emissions and Combustion in a Carbureted and PFI Small Engine

, 2007
William P. Attard, Steven Konidaris, Ferenc Hamori, Elisa Toulson, Harry C. Watson   +4 more
openalex   +2 more sources

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Taylor Series Interpolation-Based Direct Digital Frequency Synthesizer with High Memory Compression Ratio. [PDF]

Sensors (Basel)
Palomäki KI, Nurmi J.
europepmc   +1 more source