Results 211 to 220 of about 206,979 (310)

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Effect of Irreversible Compression on the Pulmonary Nodule Detection Rate in Chest Radiographs Using AI Software. [PDF]

Diagnostics (Basel)
Kohzai M, Yamamoto S, Matsushita M, Ueno Y, Tanigawa N.   +4 more
europepmc   +1 more source

The effect of increased carburetor pressure on engine performance at several compression ratios

, 1933
Oscar W Schey, Vern G Rollin
openalex   +1 more source

Computational Investigation on the Effect of Compression Ratios on Performance Characteristics of Two Stroke Free Piston Spark Ignition Engine

, 2017
S. Neelamegan, M. Nataraj, Y Ras Mathew, R. Rajasekaran   +3 more
openalex   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

In-Vitro Evaluations of Shape Memory Polymer Scaffolds With Tunable Architecture for the Endovascular Embolization of Unruptured Intracranial Aneurysms. [PDF]

J Biomech Eng
Cabaniss TL, Colby G, Liu Y, Lee H, Bohnstedt BN, Lee CH.   +5 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Beyond Cord Compression: Instability as a Major Driver for Neurological Deficit in Active Thoracic Spinal Tuberculosis. [PDF]

Global Spine J
Raghuraj Ramasamy H, Gurusamy G, K S SVA, Shetty AP, Kanna RM, Kaviprawin M, Rajasekaran S.   +6 more
europepmc   +1 more source

A study of combustion improvement of a small gasoline engine by using the high compression ratio

, 2016
Kensuke Kondo, Tadashige KAWAKAMI
openalex   +2 more sources

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source