Results 101 to 110 of about 585,711 (306)

Azarshahr travertine compression strength prediction based on point-load index (I_s) data using multilayer perceptron. [PDF]

Sci Rep, 2023
Mao Y, Licai Z, Feng L, Nanehkaran YA, Zhang M.   +4 more
europepmc   +1 more source

Durability and damage tolerance of Large Composite Primary Aircraft Structure (LCPAS) [PDF]

Analysis and testing addressing the key technology areas of durability and damage tolerance were completed for wing surface panels. The wing of a fuel-efficient, 200-passenger commercial transport airplane for 1990 delivery was sized using graphite-epoxy
Mccarty, John E., Roeseler, William G.
core   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Compression Strength Estimation of Corrugated Board Boxes for a Reduction in Sidewall Surface Cutouts-Experimental and Numerical Approaches. [PDF]

Materials (Basel), 2023
Fehér L, Pidl R, Böröcz P.
europepmc   +1 more source

Influence of bending–twisting coupling on compression and shear buckling strength [Keynote] [PDF]

, 2015
No abstract ...
York, Christopher B.
core  

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Enhancement of quasi-static compression strength for aluminum closed cell foam blocks shielded by aluminum tubes. [PDF]

Sci Rep, 2023
Dadoura MH, Farahat AIZ, Taha MR, Elshaer RN.   +3 more
europepmc   +1 more source

Mechanical characterization of timber in structural sizes: bending and compression tests [PDF]

, 2005
This paper presents the results obtained in a series of tests on Pinus Pinaster Ait. timber specimens, using the prEN408:2000, to estimate the local and global Young’s modulus and strength both in bending and compression parallel to the grain.
Branco, J., Cruz, P., Varum, H.
core   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Is there a Difference in Interfragmentary Compression Strength Between Fully or Partially Threaded Screws? Results of an Experimental Biomechanical Pilot Study. [PDF]

Rev Bras Ortop (Sao Paulo), 2023
Okoro T, Landgren M, Afenu E, Russow G, Wulsten D, Heyland M.   +5 more
europepmc   +1 more source