Results 21 to 30 of about 205,113 (309)

Mechanical properties of zirconia octet truss structures fabricated by DLP 3D printing

Materials Research Express, 2020
Zirconia ceramic octet-truss structures with various strut size and unit cell numbers were successfully fabricated through a DLP-based 3D printing method.
Weiming Zhao, Cao Wang, Bohang Xing, Minhao Shen, Zhe Zhao   +4 more
doaj   +1 more source

Fracture mechanisms and failure analysis of carbon fibre/toughened epoxy composites subjected to compressive loading [PDF]

, 2010
This study investigates the failure mechanisms of unidirectional (UD) HTS40/977-2 toughened resin composites subjected to longitudinal compressive loading.
A. Hodzic, A. Jumahat, Agarwal, Argon, Berbinau, Berbinau, Budiansky, Budiansky, C. Soutis, F.R. Jones, Hahn, Hancox, Pimenta, Soutis, Soutis, Soutis, Soutis, Waas, Weaver, Yugartis   +19 more
core   +1 more source

Non-destructive evaluation of cement-based materials from pressure-stimulated electrical emission - Preliminary results [PDF]

, 2011
This is the post-print version of the final paper published in Construction and Building Materials. The published article is available from the link below.
A. Kyriazopoulos, Anastasiadis, Anastasiadis, Aydin, C. Anastasiadis, C.J. Brown, D. Triantis, Eccles, Enomoto, Finkelstein, Griffith, Kosmatka, Kyriazopoulos, Landis, Nitsan, Ogawa, Saito, Slifkin, Stavrakas, Stavrakas, Stepanov, Sun, Sun, Sun, Triantis, Triantis, Triantis, Turcotte, Tzanis, Vallianatos, Vallianatos, Vallianatos, Vallianatos, Varotsos, Whitworth, Wittmann   +35 more
core   +1 more source

Biomechanical Tolerance of Whole Lumbar Spines in Straightened Posture Subjected to Axial Acceleration [PDF]

, 2017
Quantification of biomechanical tolerance is necessary for injury prediction and protection of vehicular occupants. This study experimentally quantified lumbar spine axial tolerance during accelerative environments simulating a variety of military and ...
Baisden, Jamie L., Chirvi, Sajal, Curry, William H., Doan, Ninh, Maiman, Dennis J., Paskoff, Glenn, Pintar, Frank A., Shender, Barry S., Stemper, Brian D., Yoganandan, Narayan   +9 more
core   +2 more sources

Extension of the Equivalent Material Concept to Compressive Loading: Combination with LEFM Criteria for Fracture Prediction of Keyhole Notched Polymeric Samples

Applied Sciences, 2021
This work analyzes, both theoretically and experimentally, the fracture process of square specimens weakened by keyhole notches and subjected to compressive stresses.
Ali Reza Torabi, Kazem Hamidi, Behnam Shahbazian, Sergio Cicero, Filippo Berto   +4 more
doaj   +1 more source

A meta-analysis of the mechanical properties of ice-templated ceramics and metals [PDF]

, 2015
Ice templating, also known as freeze casting, is a popular shaping route for macroporous materials. Over the past 15 years, it has been widely applied to various classes of materials, and in particular ceramics.
Deville, Sylvain, Meille, Sylvain, Seuba, Jordi   +2 more
core   +3 more sources

Compressive Loading of Apple Cultivar Golden Delicious

Acta Technologica Agriculturae, 2022
The study dealt with the experimental and numerical assessment of the apple cultivar Golden Delicious (Malus domestica L.) at compressive loading in lateral direction. The development of fruit hemisphere behaviour was examined between two parallel plates.
Kubík Ľubomír, Kažimírová Viera, Božiková Monika   +2 more
doaj   +1 more source

New methodology for calculating damage variables evolution in Plastic Damage Model for RC structures [PDF]

, 2017
The behavior of reinforced concrete (RC) structures under severe demands, as strong ground motions, is highly complex; this is mainly due to joint operation of concrete and steel, with several coupled failure modes.
Alfarah, Bashar, López Almansa, Francisco, Oller Martínez, Sergio Horacio   +2 more
core   +2 more sources

Experimental and Numerical Investigation on Progressive Collapse Resistance of Post-tensioned Precast Concrete Beam-Column Sub-assemblages [PDF]

, 2020
In this paper, four 1/2 scaled precast concrete (PC) beam-column sub-assemblages with high performance connection were tested under push-down loading procedure to study the load resisting mechanism of PC frames subjected to different column removal ...
Feng, D-C., Fu, F., Liang, S-L., Qian, K., Wu, G.   +4 more
core   +1 more source

A study on the influence of the loading rate and orientation on some mechanical properties of cassava tubers of different ages

Research in Agricultural Engineering, 2021
The study determined the effects of the speed of loading and the loading orientation on some selected mechanical properties of the TME 419 cassava tuber variety at different ages of the tuber which are essential in the design and construction of the ...
Olawale Ogunnigbo, Dare Adetan, Tunde Morakinyo, Olusola Olusunmade, Bolaji Ojerinde   +4 more
doaj   +1 more source