Results 101 to 110 of about 385,664 (280)

Inflammatory Response‐Inspired Thermochromic Shield for Pneumatic Structures

Advanced Engineering Materials, EarlyView.
A thermochromic shield for pneumatic structures is developed, using anhydrous sodium acetate powder and thermochromic pigment‐included solution. In this shield composed of three layers, the exothermic and thermochromic reactions, followed by the mixture of both components, occur promptly with an incident of penetrating damage as a sign of initial ...
Hyun Jae Lee, Ryuma Niiyama
wiley   +1 more source

Compressive Strength Properties of Snow [PDF]

Journal of Glaciology, 1959
AbstractThe compressive strength of snow cylinders was investigated as a function of the age of the snow from which the cylinders were made, the snow particle size and the age of the cylinders. The results show that the compressive strength is reduced if the snow is older, if the particle size is smaller, or if the cylinders are younger.
openaire   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Fatigue Damage of Rubber Concrete Backfill at Arch Springing Influence on Surrounding Rock Deformation in Tunnel Engineering

Applied Sciences
The backfill area of tunnel projects may deform or collapse due to the cyclic disturbance of groundwater and train loads. Hence, the anti-deformation and crack resistance performance of backfill materials under cyclic disturbance is critical to ...
Bo Wu, Ruonan Zhu, Zhaochun Liu, Jiajia Zeng, Cong Liu   +4 more
doaj   +1 more source

Space environmental effects on graphite-epoxy compressive properties and epoxy tensile properties [PDF]

This study characterizes the effects of electron radiation and temperature on a graphite-epoxy composite material. Compressive properties of the T300/934 material system were obtained at -250 F (-157 C), room temperature, and 250 F (121 C).
Fox, Derek J., Herakovich, Carl T., Sykes, George F., Jr.   +2 more
core   +1 more source

Recycled Glass Fiber Reinforced Polymer Composites Incorporated in Mortar for Improved Mechanical Performance [PDF]

, 2017
Glass fiber reinforced polymer (GFRP) recycled from retired wind turbines was implemented in mortar as a volumetric replacement of sand during the two phases of this study.
Englund, Karl, Fakron, Osama, Li, Hui, Nassiri, Somayeh, Rodin, Harry   +4 more
core  

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Behaviour of concrete filled stainless steel elliptical hollow sections [PDF]

, 2008
This paper presents the behaviour and design of axially loaded concrete filled stainless steel elliptical hollow sections. The experimental investigation was conducted using normal and high strength concrete of 30 and 100 MPa. The current study is based
Burdett, M., Gardner, L., Lam, D.
core  

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

Advanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source