Results 121 to 130 of about 8,248 (216)

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Grain Refinement During Severe Plastic Deformation and Similitude of Subgrain Formation: A Molecular Dynamics Study

Advanced Engineering Materials, EarlyView.
Molecular dynamics is used to investigate structure refinement during severe plastic deformation. The results show similitude with experimental data. Molecular dynamics simulations of severe plastic deformation of monocrystalline and polycrystalline samples by multiaxial compression of aluminum are carried out.
Roberto B. Figueiredo
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source