Results 131 to 140 of about 887,327 (301)
This study uncovers the unexplored role of intermolecular interactions in multiphoton absorption in coordination polymers. By analyzing [Zn2tpda(DMA)2(DMF)0.3], it shows how the electronic coupling of the chromophores and confinement in the MOF enhance two‐and three‐photon absorption.
Simon Nicolas Deger +11 more
wiley +1 more source
This study investigates H4TBAPy‐based metal–organic frameworks (MOFs) ‐ NU‐1000, NU‐901, SrTBAPy, and BaTBAPy ‐ for multiphoton absorption (MPA) performance. It observes topology‐dependent variations in the 2PA cross‐section, with BaTBAPy exhibiting the highest activity.
Simon N. Deger +10 more
wiley +1 more source
3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries
Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling +7 more
wiley +1 more source
[18F]FDG PET/CT revealing extensive cutaneous involvement in Sézary syndrome
Sézary syndrome is a rare cutaneous T-cell lymphoma characterized by erythroderma and circulating malignant T cells. This study presents the case of a 31-year-old man with extensive skin involvement detected by 2-deoxy-2-[¹⁸F]fluoro-D-glucose positron ...
Yassir Benameur +3 more
doaj +1 more source
Meta‐Rod Mechanical Metamaterials With Programmable Reconfiguration
Existing mechanical metamaterials achieve programmable large deformations in planar square or cubic configurations, restricted by required complex boundary conditions. This research proposes a 1D metamaterial, Meta‐rod, with linear, bending, twisting, area, and volume deformation modes.
Atharva Pande, Lyes Kadem, Hang Xu
wiley +1 more source
Automat optical inspection (AOI) techniques in semiconductor fabrication can be leveraged in battery manufacturing, enabling scalable detection and analysis of electrode‐ and cell‐level imperfections through AI‐driven analytics and a digital‐twin framework.
Jianyu Li, Ertao Hu, Wei Wei, Feifei Shi
wiley +1 more source
Dispensing Volumetric Additive Manufacturing
Dispensing volumetric additive manufacturing (DVAM) prints 3D structures inside a photocurable resin droplet suspended from the tip of a glass pipette, enabling sequential printing without resin vats or manual part removal. Real‐time droplet profiling and ray‐tracing‐based correction compensate for optical distortion at the curved resin‐air interface ...
Hongryung Jeon +5 more
wiley +1 more source
Here, SubNc single‐component organic photodiodes (SC‐OPDs) are investigated, which achieve highly competitive performance metrics, including high EQE, ultra‐low JD, and high specific detectivity (D*). This study emphasizes the critical role of an organic buffer layer in studying the interface energetics and effects to achieve state‐of‐the‐art ...
Anncharlott Kusber +12 more
wiley +1 more source
The aim of our study was to assess the inter-observer variability in delineation of the gross tumour volume (GTV) of oesophageal cancer on magnetic resonance (MR) in comparison to computed tomography (CT) and positron emission tomography and CT (PET/CT).
Secerov-Ermenc Ajra +6 more
doaj +1 more source
Atomic Layer Deposition in Transistors and Monolithic 3D Integration
Transistors are fundamental building blocks of modern electronics. This review summarizes recent progress in atomic layer deposition (ALD) for the synthesis of two‐dimensional (2D) metal oxides and transition‐metal dichalcogenides (TMDCs), with particular emphasis on their enabling role in monolithic three‐dimensional (M3D) integration for next ...
Yue Liu +5 more
wiley +1 more source

