Results 171 to 180 of about 598,655 (202)

In‐House Manufacturing of 3D ECM Culture Chips via Vacuum Thermoforming for Enhanced Imaging Applications

open access: yesAdvanced Materials Technologies, EarlyView.
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina   +5 more
wiley   +1 more source

Liquid Crystal Elastomer Actuator Matrix for Large Area Applications

open access: yesAdvanced Materials Technologies, EarlyView.
A scalable approach is used to manufacture a digitally‐controllable, 2D 5 × 5 actuator matrix. The elements of the matrix are produced by direct ink writing of a liquid crystal elastomer ‘artificial muscle’ on large‐area flexible thin‐film heaters. In optimizing the low‐power actuators, multiple heater designs and substrate materials are investigated ...
Giulia Spallanzani   +5 more
wiley   +1 more source

A Constraint‐Based Analytical Framework for Design‐Space Analysis and Material Screening of Tubular Multilayer Dielectric Elastomer Pumps for Extracorporeal Circulatory Applications

open access: yesAdvanced Materials Technologies, EarlyView.
A constraint‐based analytical framework maps the coupled effects of material properties, structural parameters, and operating conditions in tubular dielectric elastomer pumps for extracorporeal circulatory applications. The approach defines performance boundaries through mechanical, electrical, and hydraulic constraints and identifies feasible design ...
Yan Zhang   +3 more
wiley   +1 more source

Recent Advances in Transparent Microelectrode Device Architecture and Fabrication Strategies for Biomedical Applications

open access: yesAdvanced Materials Technologies, EarlyView.
Transparent microelectrode arrays enable simultaneous optical and electrical electrophysiology with high spatiotemporal resolution, allowing multimodal observations of dynamic biological systems. Advances in materials and device architectures improve device performance by addressing key trade‐offs between optical transparency, impedance, and ...
Michael Abraham Listyawan   +6 more
wiley   +1 more source

Hierarchically Wrinkled Silver Ink as a Platform for Fully Integrated Stretchable Electronic Systems

open access: yesAdvanced Materials Technologies, EarlyView.
Silver Hierarchical Responsive ink (SHRink), a universal approach for the fabrication of highly stretchable interconnects, wirings, and skin‐interfaced electrodes, is realized through low‐cost, scalable spray‐printing and transfer‐printing. The SHRink demonstrates high electrical conductivity (1.2E04 S cm−1) and large stretchability (235% max fracture ...
Junye Li   +11 more
wiley   +1 more source

Programming Actuation in 3D‐Printed Micro‐Architectures via Interfacial Adhesion Control

open access: yesAdvanced Materials Technologies, EarlyView.
A two‐phase meniscus‐guided 3D printing method directly fabricates microscale poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and poly(vinyl alcohol) (PVA) bilayers with in situ programmable interfaces. Modulating the meniscus stretching speed switches the interface between separated and bonded states, which controls the mechanical ...
Xiao Huan   +13 more
wiley   +1 more source

3D‐Printed Actuator Powered by Liquid Crystal Elastomer Muscles at the Water–Air Interface

open access: yesAdvanced Materials Technologies, EarlyView.
Soft robots for unstructured environments require responsive, durable actuators. Liquid crystal elastomers (LCEs) provide large reversible deformations under thermal or optical stimuli. Direct ink writing enables fabrication of LCE actuators integrated with silicone, with mesogen chemistry and oligomers optimized for printable inks.
Cecilie Ryberg   +5 more
wiley   +1 more source

Extrusion‐Based Bioprinting of Living Bioinks for Tissue and Organ Engineering

open access: yesAdvanced Materials Technologies, EarlyView.
Extrusion‐based bioprinting is presented as the most versatile route for fabricating living, heterogeneous tissues. Its ability to combine diverse bioinks, support matrices, and advanced printhead geometries transforms familiar constraints into powerful biofabrication opportunities.
Eric Silberman   +4 more
wiley   +1 more source

Thermoresponsive Self‐Healing Carbon Nanotube‐Reinforced Dual‐Network Hydrogels for Wearable Sensors and Information Concealment

open access: yesAdvanced Materials Technologies, EarlyView.
A CNT‐reinforced dual‐network hydrogel combines ionic liquid‐mediated thermoresponsiveness, dynamic covalent crosslinking, and conductive nanostructures within a single adaptive material. The hydrogel exhibits ultrafast gelation, autonomous self‐healing, >1000% stretchability, reversible optical switching, and stable electromechanical sensing, enabling
Xia Qiu   +6 more
wiley   +1 more source

Microneedles Fabrication by Substrate‐Independent Electrostretching and In‐Situ Focused Electrospray Deposition for Transdermal Drug Delivery

open access: yesAdvanced Materials Technologies, EarlyView.
A novel electrohydrodynamic platform integrating substrate‐independent in situ dried electrostretching (SI‐PIDES) and in situ focused electrospray deposition (IFED) enables mold‐free fabrication and precise drug coating of flexible core–sheath microneedle patches.
Ngoc Luan Mai   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy