Results 31 to 40 of about 3,676 (240)

IBER CONCRETE FOR 3D-PRINTING

Bulletin of Belgorod State Technological University named after. V. G. Shukhov, 2019
The article deals with the possibility of using 3D-printing in the construction industry. The analysis of the work performed in this area in the world. It also presents the main advantages of this method of construction of structures and buildings in general.
Aleksandr Klyuev, Sergey Klyuev, Elena Shorstova   +2 more
openaire   +2 more sources

3D PRINTING OF FOAMED CONCRETE

Global Journal of Science & Engineering, 2020
This paper discusses the needs for 3D printing in comparison to conventional construction and proposes foamed concrete material for printing. Example of 3D printing projects under study to overcome housing crisis are presented. Stability and sufficient strength and structural integrity are the main parameters to look for when looking of printable ...
Rabab Allouzi, Amer Alkloub
openaire   +1 more source

Tough, Ductile, and Strong Hard‐Soft Cementitious Composite Enabled by Multi‐Material Additive Manufacturing

Advanced Materials, EarlyView.
Drawing inspiration from the layered hard‐soft architecture found in sea sponges, this work establishes a new framework for architected cementitious composites (ACC) through multi‐material additive manufacturing (MMAM) process. The integration of mortar and elastomer phases into layered architectures enables synergistic toughening mechanisms, including
Aimane Najmeddine, Shashank Gupta, William Makinen, Zayvinn Lin, Krystal Delnoce, Reza Moini   +5 more
wiley   +1 more source

Designing a Habitat for 3D Concrete Printing in Permafrost Regions

Joelho, 2023
3D concrete printing has the potential to provide solutions to the global shortage of affordable housing. The technology may be particularly suitable for remote regions, where the shortage of labor and materials present challenges.
Jose Pinto Duarte, Gonçalo Duarte, Nathan Brown, Shadi Nazarian, Ali Memari, Sven Bilén, Aleksandra Radlinska   +6 more
doaj   +1 more source

Elephant‐Skin‐Inspired Porous Cementitious Tiles with Programmable Crack Networks for Passive Cooling

Advanced Materials, EarlyView.
Elephant‐skin‐inspired crack networks are programmed in porous diatomaceous earth (DE)‐cement composites using substrate‐guided, stress‐concentration induced fracture. The resulting crack lattices act as capillary conduits that redistribute water, while the porous matrix stores moisture.
Qingya Huang, Kun‐Hao Yu, Ji Yoon Bae, Yunchan Lee, Dorit Aviv, Shu Yang   +5 more
wiley   +1 more source

Incorporating coarse aggregates into 3D concrete printing from mixture design and process control to structural behaviours and practical applications: a review

Virtual and Physical Prototyping
Three-dimensional concrete printing (3DCP) is progressing from lab pilots to large-scale manufacturing, encountering limitations with conventional printable material  – cement mortar. Coarse aggregate concrete (CAC) emerges as a promising alternative due
Dong An, Y.X. Zhang, Richard (Chunhui) Yang   +2 more
doaj   +1 more source

Neuromorphic Electronics for Intelligence Everywhere: Emerging Devices, Flexible Platforms, and Scalable System Architectures

Advanced Materials, EarlyView.
The perspective presents an integrated view of neuromorphic technologies, from device physics to real‐time applicability, while highlighting the necessity of full‐stack co‐optimization. By outlining practical hardware‐level strategies to exploit device behavior and mitigate non‐idealities, it shows pathways for building efficient, scalable, and ...
Kapil Bhardwaj, Roshni Satheesh Babu, Yuxin Xia, Eva Bestelink, Radu Sporea, Nikos Hastas, Ioannis Zeimpekis, Dimitra G. Georgiadou, Sayani Majumdar   +8 more
wiley   +1 more source

3D printed concrete using Portland pozzolana cement - fly ash based [PDF]

E3S Web of Conferences
This project investigates the feasibility and properties of 3D printed concrete using Portland Pozzolana Cement (PPC). The increasing demand for construction materials, particularly ordinary Portland cement (OPC), has led to a surge in its usage ...
Ibrahim A Mohamed, Kumar N Senthil
doaj   +1 more source

Organic Materials of Tomorrow: Horizons of Artificial Intelligence

Advanced Materials, EarlyView.
This review examines machine learning techniques accelerating the discovery of organic semiconductors by linking molecular structure to properties. Key methods include graph neural networks, generative models, and active learning. Applications to organic photovoltaics demonstrate practical impact.
Harold Mena, J. Terence Blaskovits, Kun‐Han Lin, Denis Andrienko   +3 more
wiley   +1 more source

Additive‐Manufactured, Multifunctional Bioreactor Technology for Dynamic Culture of 3D Bioprinted Tissue Models

Advanced Materials Technologies, EarlyView.
We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger, Johann Schorzmann, Hsuan‐Heng Lu, Muhammad Osama, Julian Bauer, Michael Haug, Oliver Friedrich, Aldo R. Boccaccini, Frank Döpper, Sahar Salehi   +9 more
wiley   +1 more source