Results 71 to 80 of about 16,666 (192)

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Bioimage analysis for multiplexed FUCCI acquisitions powered by deep learning. [PDF]

Npj Imaging
Zimmermann J, Pezzotti M, Torchia E, Enrico A, Rigolli S, Di Sante M, Pasqualini FS.   +6 more
europepmc   +2 more sources

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

Advanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu, Timon Steinhoff, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Christian Klose, Ludger Overmeyer, Hans‐Jürgen Maier, Nina Merkert   +8 more
wiley   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

Advanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin, Marvin Erck, Kevin Jasutyn, Katja Radermacher, Andreas Bund, Mario Kurniawan   +5 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

Scale-Invariant Waveguiding in Flatland. [PDF]

Exploration (Beijing)
Xu Z, Bao S, Moccia M, Castaldi G, Cui TJ, Galdi V.   +5 more
europepmc   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source