Results 111 to 120 of about 1,275 (269)

Nocturnal Intraocular Pressure Monitoring With a Soft Contact Lens Sensor for Glaucoma Management

Advanced Materials, EarlyView.
A soft contact lens sensor enables continuous, noninvasive monitoring of nocturnal intraocular pressure (IOP) under closed‐eye sleep conditions. By integrating a highly compliant inductive–capacitive circuit onto a commercial lens, the device achieves record sensitivity and stable performance.
Yumin Dai, Tristan Michael Long, Oluwabunmi T. Oladele, Youngoh Lee, Feiyang Li, Ziheng Wang, Yeonji Oh, Junsang Lee, Taewoong Park, Tianhao Yu, Seokkyoon Hong, Kyeonghee Lim, Jinheon Jeong, Dawn Meyer Schneider, Hyerim Ra, Bryan W. Boudouris, Gillian C. Shaw, Shin Ae Park, Pete S. Kollbaum, Chi Hwan Lee   +19 more
wiley   +1 more source

Ti3C2Tx MXene/Silver Composite Foams For Lightweight, High‐Performance Electromagnetic Interference Shielding and Joule Heating

Advanced Materials Interfaces, EarlyView.
Ultrathin MXene/EMF composite foams achieve a specific shielding efficiency of 749.6 dB.dB·cm3$\mathrm{dB}\cdot {\mathrm{cm}}^{3}$/g, while the silver‐enhanced MXene/Ag/EMF reaches 81.4 dB shielding effectiveness at just 1.0 mm thickness. Both composites exhibit rapid Joule heating, retain stability up to 250∘C$^\circ{\rm C}$, and withstand 1000 ...
Abdullah A. Mahmood, Mingxuan Li, Vahid Rad, Mehdi Zarei, Chen‐Yu Yeh, Masoud Soroush, Guangyong Li, Paul W. Leu   +7 more
wiley   +1 more source

Shadow‐Free Back‐Contact Perovskite Thin‐Film Detectors for Direct Extreme‐Ultraviolet and Soft X‐Ray Sensing

Advanced Materials Interfaces, EarlyView.
A triple‐cation perovskite detector with a quasi‐interdigitated back‐contact architecture enables highly sensitive and linear EUV/soft x‐ray detection by minimizing electrode shadowing and enhancing charge extraction. Efficient interfacial carrier collection and rapid temporal response highlight the potential of back‐contact‐engineered perovskites for ...
Jingying Liu, Siqi Deng, Mosarof Hossain, Udo Bach, Kaijian Xing, Qingdong Ou   +5 more
wiley   +1 more source

Additively manufactured conformal cooling channels through topology optimization

Structural and Multidisciplinary Optimization
AbstractCooling channels play a critical role in various casting and molding processes, impacting both the cycle time and quality of the product. As additive manufacturing technologies become increasingly prevalent, conventional straight-drilled channels are being progressively substituted by intricate cooling lines that conform to the contours of the ...
Lamarche-Gagnon, Marc-Étienne, Molavi-Zarandi, Marjan, Raymond, Vincent, Ilinca, Florin   +3 more
openaire   +2 more sources

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Liquid Metal‐Based Stretchable Strain Sensor for Fruit Growth Monitoring

Advanced Materials Technologies, EarlyView.
Schematic overview of the fruit growth sensor development workflow, including sensor fabrication by injection molding, electromechanical and environmental characterization, mechanical stability testing, electronic readout integration, and outdoor field validation for monitoring of fruit growth under practical orchard conditions.
Asad Ullah, Lennert Purnal, Maximilian Krack, Sander Vijgen, Thijs Vandenryt, Dieter Reenaers, Ronald Thoelen, Wim Deferme   +7 more
wiley   +1 more source

Design and simulation study of effective cooling channel for injection moulded plastic part

, 2017
Injection moulding (IM) process has significant impact on plastic manufacturing process. In IM process cycle, cooling time carries almost half of its cycles time where cooling channel performance is one of the most crucial factors because it has ...
Maitham Abonassrya (19103987), Abul Saifullah (18923314), Safaa Alabid (19103990)   +2 more
core   +1 more source

Multimodal Haptic Perception Through Synergistic Nanocomposite Sensor Arrays

Advanced Materials Technologies, EarlyView.
Multi‐modal fingertip haptics are advanced through a bioinspired &vertical‐via' electronic skin architecture. A confined PDMS/MWCNT/NiNP nanocomposite, sitting at the percolation threshold, enables tactile, thermal, and magnetic sensing. A unique via‐density gradient and dedicated &Un‐Touch' reference nodes provide robust spatial resolution and signal ...
Amos Bardea, Fernando Patolsky
wiley   +1 more source

On Optimization of Injection Molding Cooling [PDF]

, 2008
This thesis is devoted to analysis and optimization of the injection molding process with a focus on the mold. In the analysis, both process parameters and the design of the mold are taken in consideration. A procedure has been developed, i.e.
Rännar, Lars-Erik
core  

Flexible Pressure Sensor With Co‐Optimized Sensitivity and Linearity Based on Gradient Toroidal Microstructures

Advanced Materials Technologies, EarlyView.
A flexible piezoresistive pressure sensor with gradient toroidal CNT/PDMS microstructures is reported. The hierarchical geometry enables sequential electrode contact, achieving a sensitivity of 256.20 kPa−1 and linear response (R2 = 0.99) over 0–1000 kPa.
Rongmei Wang, Ruolin Liu, Ming Lei, Yifan Liu, Fengming Hu, Bing Ji, Chao Peng, Jianyi Luo, Bingpu Zhou   +8 more
wiley   +1 more source