Results 71 to 80 of about 21,694,057 (311)

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Optimizing Post Friction Stir Welding Heat Treatment in Dissimilar Friction Stir Welded 6061/AlSi10MgMn Joints for Electrical Vehicle Battery Housing

Advanced Engineering Materials, EarlyView.
Microstructural evolution and hardness optimization along the cross‐section of friction stir welded AA6061/AlSi10MgMn joints, for electric vehicle battery housings, were investigated. Postweld aging between 170°C and 220°C enhances hardness uniformity within the nugget zone.
Emanuele Ghio, Emanuela Cerri
wiley   +1 more source

Geometrical analysis, for rapid prototyping, of the compressor’s helical conic rotor model

MATEC Web of Conferences, 2018
The conical rotary compressor represents a solution for gases compression, for relatively small flow, in conditions of a superior energetic efficiency.
Baroiu Nicuşor, Păunoiu Viorel, Teodor Virgil Gabriel, Susac Florin, Oancea Nicolae   +4 more
doaj   +1 more source

Robust Resistance Network Topology Design by Conic Optimization

Sultan Qaboos University Journal for Science, 2012
After a brief introduction to the field of Conic Optimization we present an application to the (robust) resistor network topology design problem, where the goal is to design an electrical network containing resistors, such that the dissipation is minimal,
C. Roos, Y. Bai, D. Chaerani
doaj   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Optimal Allocation Stochastic Model of Distributed Generation Considering Demand Response

Energies
Demand response (DR) can improve the accommodation of renewable energy and further affect the distributed generation (DG) allocation strategy. In this context, this paper proposes a stochastic optimal allocation model of DG, considering DR.
Shuaijia He, Junyong Liu
doaj   +1 more source

Developing robust nonlinear models through bootstrap aggregated deep belief networks

AIMS Electronics and Electrical Engineering, 2020
Deep belief network (DBN) has recently emerged as a powerful tool in building nonlinear data driven models. However, a single DBN model can still lack reliability especially when the amount of data available for modelling is limited.
Changhao Zhu, Jie Zhang
doaj   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Transfer of Energy and Momentum Between Magnetoactive Surface Microstructure and a Solid Object

Advanced Engineering Materials, EarlyView.
We demonstrate that magnetoactive multilamellar arrays subjected to a rotating magnetic field can function as platforms for controlled transport of physical objects. Through systematic experimental investigation, we elucidate the underlying physical mechanisms determining the upper limit of the achievable transportation speed in such magnetic “conveyor‐
Arne Geldof, Jan Kopačin, Izidor Straus, Raphael Kriegl, Gaia Kravanja, Luka Hribar, Matija Jezeršek, Mikhail Shamonin, Gašper Kokot, Irena Drevenšek‐Olenik   +9 more
wiley   +1 more source

Advancing Electronic Application of Coordination Solids: Enhancing Electron Transport and Device Integration via Surface‐Mounted MOFs (SURMOFs)

Advanced Functional Materials, EarlyView.
The layer‐by‐layer (LbL) assembly of coordination solids, enabled by the surface‐mounted metal‐organic framework (SURMOF) platform, is on the cusp of generating the organic counterpart of the epitaxy of inorganics. The programmable and sequential SURMOF protocol, optimized by machine learning (ML), is suited for accessing high‐quality thin films of ...
Zhengtao Xu, Christof Wöll, Stefan Bräse   +2 more
wiley   +1 more source