Results 121 to 130 of about 336,920 (287)

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Screen‐Printed Flexible Piezoelectric Force Sensor Array with Electromagnetic Interference Shielding

Advanced Engineering Materials, EarlyView.
This article introduces a flexible screen‐printed piezoelectric sensor array designed for low‐frequency healthcare applications such as tactile sensing and cardiovascular monitoring. The device integrates interface electronics enabling the simultaneous acquisition of up to 128 signals, along with flexible EMI shielding that significantly reduces noise ...
Joseph Faudou, Mohammed Benwadih, Arnaud Gabas, Lina Kadura, Minh‐Quyen Le, Daniel Grinberg, Pierre‐Jean Cottinet   +6 more
wiley   +1 more source

Cost-effective aperture arrays for SKA Phase 1: single or dual-band?

, 2012
An important design decision for the first phase of the Square Kilometre Array is whether the low frequency component (SKA1-low) should be implemented as a single or dual-band aperture array; that is, using one or two antenna element designs to observe ...
Colegate, T. M., Gunst, A. W., Hall, P. J.   +2 more
core  

Sustainable Synthesis of Bio‐Based Magnetic and Conductive Wood for Electromagnetic Interference Shielding Applications

Advanced Engineering Materials, EarlyView.
A wood‐based magnetic and conductive material called Magwood (MW), capable of blocking almost 99.99% of electromagnetic waves (in the X‐band frequency range), is synthesized using a simple, solvent‐free process. MW is lightweight, resists water, and is flame‐retardant, making it a promising alternative for shielding electronics. The rapid proliferation
Akash Madhav Gondaliya, Majed Amini, Mohammad Arjmand, Earl Johan Foster   +3 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Engineering Deformation and Failure in Diamond Triply Periodic Minimal Surface Lattices via 3D Wall‐Thickness Grading

Advanced Engineering Materials, EarlyView.
The work demonstrates that strategic wall‐thickness grading in diamond triply periodic minimal surface lattices enables precise tuning of deformation and failure behavior under compression. Different gradation patterns guide how and where the structure collapses, improving energy absorption or promoting controlled brittle failure.
Giovanni Rizza, Danilo Bruson, Manuela Galati, Luca Iuliano   +3 more
wiley   +1 more source

Measurement-based long-range entangling gates in constant depth

Physical Review Research
The depth of quantum circuits is a critical factor when running them on state-of-the-art quantum devices owing to their limited coherence times. Reducing circuit depth decreases noise in near-term quantum computations and reduces overall computation time.
Elisa Bäumer, Stefan Woerner
doaj   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

Advanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source

Analyzing Electronic Excitations and Exciton Binding Energies in Y6 Films

Advanced Functional Materials, EarlyView.
The Y6 molecule is used for increasing the efficiency of organic solar cells. The exciton binding energy is calculated for ensembles of Y6 molecules that are representative of the typically used films. The calculations show that the excitons typically spread out over many molecules.
Sahar Javaid Akram, Sophie Meißner, Stephan Kümmel   +2 more
wiley   +1 more source

Verifying constant-time implementations in a verified compilation toolchain

, 2018
Side-channel attacks are an especially dangerous form of attack. In this thesis, we focus on the timing side-channel. A program is said to be constant-time if it is not vulnerable to timing attacks. We present in this thesis two methods relying on static analysis in order to ensure that a program is constant-time.
openaire   +1 more source