Results 151 to 160 of about 1,321,024 (261)

Low‐Activation Compositionally Complex Alloys for Advanced Nuclear Applications—A Review

Advanced Engineering Materials, EarlyView.
Low‐activation compositionally complex alloys (LACCAs) are advanced metallic materials primarily composed of low‐activation elements, offering advantages such as rapid compliance with operational standards and safe recyclability. This review highlights their potential for extreme high‐temperature irradiation environments as structural materials for ...
Yangfan Wang, Hanliang Zhu, Zhiyang Wang, Zhijun Qiu, Xiao Wang, Zengxi Pan, Hongtao Zhu, Mingxing Zhang, Huijun Li   +8 more
wiley   +1 more source

High‐Entropy Ti, Zr, Hf, Ta Multiphase Diboride with Deformation Resistance up to 2000 °C

Advanced Engineering Materials, EarlyView.
Ceramics are brittle and strength decreases with temperature. The multiphase high‐entropy (Ti0.25Ta0.25Hf0.25Zr0.25)B2 with heterogeneity at the nano‐ and microscale demonstrates deformation resistance up to 2000 °C, with maximum bending strength at 1800 °C.
Petre Badica, Mihai Alexandru Grigoroscuta, Andrei Cristian Kuncser, Oleg Vasylkiv   +3 more
wiley   +1 more source

A Study on Thermal Expansion and Thermomechanical Behavior of Composite Metal Foams

Advanced Engineering Materials, EarlyView.
The coefficient of thermal expansion of steel–steel composite metal foam (S‐S CMF) is shown to be lower than that of bulk stainless steel while its performance under compression demonstrate excellent mechanical stability and strength at all temperatures with gradualsoftening from 400 to 600 °C.
Zubin Chacko, Nigel Amoafo Yeboah, Afsaneh Rabiei   +2 more
wiley   +1 more source

Fabrication of Compositionally Graded NiTi Shape Memory Alloy Laminated Composites Through Hot Roll Bonding and its Characterization

Advanced Engineering Materials, EarlyView.
A novel technique for fabricating monolithic functionally graded NiTi shape memory alloy (SMA) laminated hybrid composite has been developed. An excellent metallurgical bonding can be established between two compositionally different NiTi SMAs through spark plasma sintering joining/diffusion bonding followed by hot roll bonding.
Soumya Sinha, Bikas Chandra Maji, Ram Niwas Singh   +2 more
wiley   +1 more source

Low‐Velocity Penetration Impact Behavior of Triply Periodic Minimal Surface Strut‐Based Lattices

Advanced Engineering Materials, EarlyView.
Triply periodic minimal surface (TPMS)‐based lattices are gaining attention for their multifunctional properties in applications as aeronautics and automotive, which involve low‐velocity impact loading. This work evaluates the low‐velocity penetration impact behavior of five distinct TPMS architectures.
Lucía Doyle, Javier García‐Molleja, Carlos González   +2 more
wiley   +1 more source

Impacts of Device Geometry and Layout on Temperature Profile during Large‐Area Photonic Curing

Advanced Engineering Materials, EarlyView.
The study investigates how gate geometry affects peak curing temperature during photonic curing of solution‐processed indium zinc oxide thin‐film transistors. Using 3D simulations and experimental validation, it reveals that larger gate areas and smaller aspect ratios increase curing temperature and thus improve transistor performance. Findings provide
Yasir Fatha Abed, Neel Chatterjee, Bing Luo, Sarah L. Swisher   +3 more
wiley   +1 more source

Microstructure, Mechanical Properties, and Antibacterial Performance of Novel Fe‐Mn‐Zn Nanocrystalline Alloys Produced by Mechanical Alloying

Advanced Engineering Materials, EarlyView.
This article presents the development of Fe‐Mn‐Zn nanocrystalline alloys (0–9 wt% Zn) by mechanical alloying and subsequently hot pressing. Their microstructure, density, hardness, wear resistance, corrosion behavior, and antibacterial properties are systematically examined.
Ilker Emin Dag, Funda Kilic, Mrutyunjay Panigrahi, Baris Avar   +3 more
wiley   +1 more source

Scalable Manufacturing of Radiation‐Tolerant Potentiometric Electrodes: A Systematic Transition from Laboratory to Semiautomated Fabrication

Advanced Engineering Materials, EarlyView.
Laboratory protocols for producing thin‐film pH electrodes for sterilized single‐use technologies have been successfully developed into a semiautomated workflow, with higher throughput and precision of membrane thickness. Accuracies are within 0.05 pH units versus ground truth, and uncertainty analysis reveals the largest sources of error to be derived
Bingyuan Zhao, Aiganym Yermembetova, Benson Kunhung Tsai, Jialong Huang, Alexander Wei   +4 more
wiley   +1 more source

Mechanical and Microstructural Effects of ZrO2 Nanoparticles in Fe20Cr Oxide Dispersion‐Strengthened Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
The influence of oxide nanoparticle synthesis route and concentration on microstructure and high‐temperature performance of additively manufactured oxide dispersion‐strengthened steels is investigated. Comparing laser‐generated and chemically synthesized ZrO2 nanoparticles, the study reveals how dispersion quality, crystal structure and particle size ...
Mareen Goßling, Silja‐Katharina Rittinghaus, Felix Radtke, Abdelrahman Elsayed, Marina Macias Barrientos, Ulf Ziesing, Louis Becker, Ihsan Murat Kuşoğlu, Christoph Broeckmann, Ulrich Krupp, Avinash Hariharan, Sebastian Weber, Bilal Gökce   +12 more
wiley   +1 more source

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source