Results 111 to 120 of about 75,987 (284)

Does Long‐Term Lower Extremity Strength Training in Adults With Knee Osteoarthritis and Varus Alignment Reduce Knee Joint Loading During Gait?

Arthritis Care &Research, EarlyView.
Objective We examined whether 18 months of strength training in individuals with knee varus alignment and medial tibiofemoral osteoarthritis (OA) reduced knee joint loads during walking compared to an attention control group. Methods This study was a secondary analysis of a randomized clinical trial that compared the effects of strength training to a ...
Stephen P. Messier, Matthew N. Vigliotti, Paige E. Rice, Brian Pietrosimone, Shannon L. Mihalko, Edward H. Ip, Richard F. Loeser, David J. Hunter, Ali Guermazi, Ryan Hill, Santiago Saldana, Kim L. Bennell, Paul DeVita   +12 more
wiley   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Research on Probabilistic Shaping of Spiral Constellations in Visible Light Communication

Guangtongxin yanjiu
ObjectiveVisible Light Communication (VLC) is a wireless communication technology that uses the visible light band for signal transmission, integrating both lighting and communication functions.
GUO Xinyue, WANG Yue, YANG Yufan
doaj  

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Neural Network-Based Single-Carrier Joint Communication and Sensing: Loss Design, Constellation Shaping and Precoding

IEEE Access
We investigate the impact of higher-order modulation formats on the sensing performance of single-carrier joint communication and sensing (JCAS) systems.
Charlotte Muth, Benedikt Geiger, Daniel Gil Gaviria, Laurent Schmalen   +3 more
doaj   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Analysis of DWDM-based Beyond 100 Gbit/s Hybrid Networking

Guangtongxin yanjiu
【Objective】In recent years, data communication traffic has experienced explosive growth. To meet the demands for high-speed, high-capacity data transmission and the diverse network application scenarios, hybrid network beyond 100 Gbit/s (B100 Gbit/s ...
CHEN Yunchang, MEI Liang, HE Mingwen, GAO Jitao   +3 more
doaj  

Bi-GRU Enhanced Cost-Effective Memory-Aware End-to-End Learning for Geometric Constellation Shaping in Optical Coherent Communications

IEEE Photonics Journal
We propose a cost-effective and memory-aware end-to-end learning scheme utilizing bi-directional gated recurrent unit (bi-GRU) for geometric constellation shaping (GCS) under the first-order regular perturbation (FRP) auxiliary channel.
Zhiyang Liu, Xiaoyu Liu, Shilin Xiao, Weiying Yang, Weisheng Hu   +4 more
doaj   +1 more source