Results 51 to 60 of about 3,715 (260)

Evidence for Itinerant Ferromagnetic Flat Bands Producing Large Transverse Responses

Advanced Materials, EarlyView.
Itinerant ferromagnetic flat bands are demonstrated in GdCo5 with a high Curie temperature of 940K, a stacked honeycomb–kagome lattice, through angle‐resolved photoemission spectroscopy and magneto‐thermoelectric measurements. These topological flat bands generate large Berry curvaturte, producing gigantic anomalous Nernst effect with record‐high ...
Susumu Minami, Yangming Wang, Seigo Souma, Hiroto Nakamura, Akito Sakai, Takumi Osumi, Hang Su, Hikaru Watanabe, Shun'ichiro Kurosawa, Rikuto Oiwa, Daisuke Nishio‐Hamane, Kosuke Nakayama, Takuya Nomoto, Ryotaro Arita, Takafumi Sato, Satoru Nakatsuji   +15 more
wiley   +1 more source

Economic Aspects of Demolition: Challenges and Prospects—A Case Study in the Municipality of Caivano (Campania, Italy)

Buildings
The end-of-life phase of a building, which includes demolition and waste disposal, represents a crucial aspect of sustainable construction. In Europe, construction and demolition (C&D) waste accounts for approximately 40% of the total waste generated in ...
Daniela Menna, Fabrizio Battisti, Chiara Chioccarelli, Fabiana Forte, Giorgio Frunzio   +4 more
doaj   +1 more source

Spatial strategic planning for optimal management of construction waste with recycling and reuse approach in Iran [PDF]

مهندسی و مدیریت ساخت, 2022
Construction waste as a result of human construction activities on earth has caused many environmental problems. If the life cycle of the building, the three main stages of demolition, design and implementation are considered, each of them carries ...
Samaneh Javadifard, Fariborz Karimi
doaj  

Leaftronics: Bio‐Fractal Scaffolds From Leaf Venation for Low‐Waste Electronics

Advanced Materials, EarlyView.
“Leaftronics” transforms naturally evolved leaf venation into quasi‐fractal scaffolds for sustainable electronics. Polymer‐infiltrated leaf skeletons can be used to fabricate ultra‐smooth, reflow‐ and thin‐film‐compatible decomposable substrates, while making the same lignocellulose networks conducting results in flexible transparent electrodes.
Rakesh Rajendran Nair, Hrisheekesh Thachoth Chandran, Karl Leo, Hans Kleemann   +3 more
wiley   +1 more source

Study of recycling demolition waste material product in Jakarta, Indonesia

E3S Web of Conferences, 2018
Construction activities (construction and demolition) is one of the major contributors in the generation of waste generation in landfills. Recycling waste of demolition construction is considered effective, but for the case in Indonesia not many know the
Sembiring Fransisca Theresia
doaj   +1 more source

BioEISense: A Microfluidic Platform for Real‐Time Monitoring of Staphylococcus aureus Biofilm Formation and the Efficacy of Antibiofilm Agents

Advanced Materials Interfaces, EarlyView.
BioEISense is a microfluidic device with integrated impedance sensors, for real‐time, label‐free monitoring of S. aureus biofilms. In this study, the biofilm culture conditions were optimized to support sensitive and reproducible detection of biofilm formation and eradication under dynamic flow‐through conditions. The system was also validated for both
Jéssica Amorim, Laura Vesalainen, Loïc Dreano, Markus Haapala, Cristina D. Cruz, Päivi Tammela, Tiina M. Sikanen   +6 more
wiley   +1 more source

Waste Management in a Sustainable Circular Economy as a Part of Design of Construction

Applied Sciences, 2022
The Architecture, Engineering, and Construction (AEC) industries are the producers of the most significant waste stream in the European Union. Known EU initiatives propose to deal with the issue of construction and demolition waste (CDW) according to the
Marcela Spišáková, Tomáš Mandičák, Peter Mésároš, Matej Špak   +3 more
doaj   +1 more source

Bidirectional Process Prediction in the Laser‐Induced‐Graphene Production Using Blackbox Deep Learning

Advanced Materials Technologies, EarlyView.
This study shows that a lightweight blackbox neural network provides a practical, cost‐effective solution for bidirectional process prediction in laser‐induced graphene (LIG) fabrication. Achieving high predictive performance with minimal overhead, the approach democratizes machine learning (ML) for resource‐limited environments.
Maxim Polomoshnov, Nitheesh M. Nair, Gerardo Hernández‐Sosa, Markus Reischl   +3 more
wiley   +1 more source

Adopting the Zero Waste Concept for Eliminating C&D Waste in the Construction Industry [PDF]

MATEC Web of Conferences, 2019
Construction industry is one of the key economic players in any region, where Construction and Demolition (C&D) waste generation occurs due to continuous construction and demolition activities.
Liyanage K.L.A.K.T., Waidyasekara K.G.A.S., Mallawaarachchi H.   +2 more
doaj   +1 more source

Agar‐Based Optical Sensing System With a Phosphorescent Grid Pattern for Measuring Stress Distributions of Root Growth Using the Sampling Moiré Method

Advanced Materials Technologies, EarlyView.
This paper presents an agar medium with a phosphorescent grid pattern that measures the stress distribution generated by growing plant roots. Using phosphorescence, the system optically separates the grid pattern from the root and extracts the grid deformation.
Gakuto Kagawa, Hidetoshi Takahashi
wiley   +1 more source