Results 91 to 100 of about 1,439,160 (239)
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Determination of the Strength of Adhesion between Lipid Vesicles
The Scientific World Journal, 2012 A commonly used method to determine the strength of adhesion between adhering lipid vesicles is measuring their effective contact angle from experimental images.
Tomáš Mareš +4 more
doaj +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source
Investigation of drop dynamic contact angle on copper surface
EPJ Web of Conferences, 2015 This paper presents experimental results of the studying the effect of surface roughness, microstructure and flow rate on the dynamic contact angle at spreading of distilled non deaerate water drop on a solid horizontal substrates. Copper substrates with
Orlova Evgenija +2 more
doaj +1 more source
DETERMINATION OF CONTACT WETTING ANGLE ON FLAT SURFACES
Наука и техника, 2006 The paper considers an improved technique for determination of a contact wetting angle. Description of the devices that make it possible to determine a contact wetting angle with due account of surface roughness is given in the paper. A specified formula
M. G. Kiselev +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source
Validating contact angle algorithms for droplets in parallel-plate [PDF]
AIP AdvancesParallel-plate channels, defined as two closely spaced plates confining fluid motion, are widely used in microfluidics. Optical contact angle measurement techniques are particularly suited for analyzing capillary phenomena in such configurations.
Yiping Xu +7 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar +7 more
wiley +1 more source
The Case Studies of Varied Switches for the Varied Wheel Profiles of the Railway Vehicle in Terms of the Derailment Phenomena [PDF]
International Journal of Railway Research, 2015 The flange climb derailment is one of the cause of derailment for a typical switch. The derail Insert Page Break for Printingment for the switch is a complex phenomenon since the contact area is changing dynamically.
Veysel Arlı +3 more
doaj
Advanced Engineering Materials, EarlyView.This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay +3 more
wiley +1 more source