Results 251 to 260 of about 269,665 (298)
Some of the next articles are maybe not open access.
2011
In Chaps. 1 through 5 we discussed the solution of discrete, lumped-parameter models. For multiple degree of freedom systems, we employed modal analysis to enable us to transform the coupled equations of motion in local (model) coordinates into modal coordinates. In this coordinate frame, the equations of motion were uncoupled and we could apply single
Tony L. Schmitz, K. Scott Smith
openaire +1 more source
In Chaps. 1 through 5 we discussed the solution of discrete, lumped-parameter models. For multiple degree of freedom systems, we employed modal analysis to enable us to transform the coupled equations of motion in local (model) coordinates into modal coordinates. In this coordinate frame, the equations of motion were uncoupled and we could apply single
Tony L. Schmitz, K. Scott Smith
openaire +1 more source
Single Beam Load Test of Continuous Beam
Applied Mechanics and Materials, 2014GengYuHe bridge was a prestressed concrete continuous box girder bridge,based on the static load test of single beam bridges compared with theoretical calculation value,check whether the actual control section stress of the bridge are in conformity with the design requirements,and give advice.
Ya Xun Yang, Wei Ya Fan
openaire +1 more source
Aircraft Engineering and Aerospace Technology, 1942
PROBLEMS relating to built‐in or rigid‐end members under transverse loading are frequently encountered by the aircraft engineer. In the following paper discussion of relevant theorems leads to the development of Clapeyron's Theorem of Three Moments. The latter is particularly valuable in, for example, estimating the crankshaft bearing loads in a non ...
openaire +1 more source
PROBLEMS relating to built‐in or rigid‐end members under transverse loading are frequently encountered by the aircraft engineer. In the following paper discussion of relevant theorems leads to the development of Clapeyron's Theorem of Three Moments. The latter is particularly valuable in, for example, estimating the crankshaft bearing loads in a non ...
openaire +1 more source
1975
In the preceding chapter we have used the hereditary integrals and the correspondence principle for the analysis of viscoelastic beams. We have seen how both approaches may be applied even to structures which consist of several materials with different kinds of viscoelastic response.
openaire +1 more source
In the preceding chapter we have used the hereditary integrals and the correspondence principle for the analysis of viscoelastic beams. We have seen how both approaches may be applied even to structures which consist of several materials with different kinds of viscoelastic response.
openaire +1 more source
2018
Continuity provides an economic benefit with shallow sections and longer spans possible. Continuity also inherently improves safety due to the redundancy provided by the continuity. This comes at a price of increased calculation and detailing complexity, increased construction complexity, and increased propensity for cracking and other distress due to ...
Charles W. Dolan, H. R. Hamilton
openaire +1 more source
Continuity provides an economic benefit with shallow sections and longer spans possible. Continuity also inherently improves safety due to the redundancy provided by the continuity. This comes at a price of increased calculation and detailing complexity, increased construction complexity, and increased propensity for cracking and other distress due to ...
Charles W. Dolan, H. R. Hamilton
openaire +1 more source
A slow, continuous beam of cold benzonitrile
Physical Chemistry Chemical Physics, 2015A cold, continuous, high flux beam of benzonitrile has been created via buffer gas cooling.
Patterson, David, Doyle, John
openaire +3 more sources
Vibrations of Continuous Beams
1991This chapter describes how to use a FORTRAN computer program for determining the resonant frequencies and eigenmodes for encastre and continuous beams.
openaire +1 more source
1969
A beam is said to be built-in or encastre when both its ends are rigidly fixed so that the slope remains horizontal. Usually also the ends are at the same level.
openaire +1 more source
A beam is said to be built-in or encastre when both its ends are rigidly fixed so that the slope remains horizontal. Usually also the ends are at the same level.
openaire +1 more source
Numerical analysis of the shear behavior of FRP-strengthened continuous RC beams having web openings
Engineering Structures, 2021Walid Mansour
exaly