Results 81 to 90 of about 517 (173)

Evolution law of corona bond of non-magnetic drill rod weld by friction welding

Hanjie xuebao
In this paper, experiments and numerical simulations were conducted to study the evolution law of the corona bond at the interface of non-magnetic steel by continuous drive friction welding and the reasons for the appearance of banded structures at the ...
Tiantian XUE, Shiqing WANG, Guodong WEN, Junlei QI, Wang GAO, Xiaowei LUO, Yongxin LU   +6 more
doaj   +1 more source

Investigation of the mechanical properties of Inconel 718 and AISI 316L welded materials using continuous drive friction welding

Kovove Materialy-Metallic Materials
Scientific Research Project Fund of Sivas Cumhuriyet University [M-789]
Ömer Karabey, Ahmet Akkuş, Mehmet Akif Hafizoğlu   +2 more
openaire   +2 more sources

Physical Anchoring‐Assisted Mechanically Guided Assembly for Material‐Independent 3D Mesostructures

Small, Volume 22, Issue 44, 7 August 2026.
Conventional mechanically guided 3D assembly relies on selective chemical bonding between 2D precursors and elastomeric substrates, imposing fundamental limitations on material compatibility and scalability. Here, we present a physically anchored, buckling‐guided assembly platform based on a rod array patterned elastomeric substrate (RPES).
Yeonhee Heo, Pei Liu, Jeongmin Yoo, Jae Hyuk Hwang, Gooyoon Chung, Dong‐Gyun Kim, Raudel Avila, Yoonseok Park   +7 more
wiley   +1 more source

Uncovering hidden bias in neutron diffraction residual strain measurements

Journal of Applied Crystallography, Volume 59, Issue 4, Page 991-1004, August 2026.
This work demonstrates that diffraction‐based residual strain calculations and uncertainty estimates depend on how grain populations are sub‐sampled, with important implications for interpreting residual stresses in heterogeneous materials with fine‐scale microstructure and strain gradients.When calculating residual strain via neutron or X‐ray ...
Cole Franz, Michael Prime, Jeffrey Bunn, Andrew Payzant, Katharine Page   +4 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

EFFECTS OF PRESSURE IN CONTINUOUS DRIVE FRICTION WELDING ON AISI 304 AND A36

MM Science Journal, 2020
Helmy Purwanto, Muhammad Dzulfikar, Iman Syafaat, Sohabat Imanu, Nur Kholis   +4 more
openaire   +2 more sources

THE STRENGTH AND FRACTURE MORPHOLOGY OF SIMILAR AND DISSIMILAR CONTINUOUS DRIVE FRICTION WELDING

Journal of Engineering Research (Libya), 2017
Hussein Mesmari, Fawzia Krayem
openaire   +1 more source

Microjoining for biomedical device fabrication: a perspective. [PDF]

Adv Mater Join
Zhang K, Zhou YN, Peng P.
europepmc   +1 more source

An RSM-Based Investigation on the Process-Performance Correlation and Microstructural Evolution of Friction Stir Welded 7055 Al/2195 Al-Li Dissimilar T-Joints. [PDF]

Materials (Basel)
Lin B, Han Y, Zuo D, Wang N, Zhang Y, Fu H, Gao C.   +6 more
europepmc   +1 more source

An open-source BLDC motor test bed utilizing ESC telemetry for cost-effective educational laboratories. [PDF]

HardwareX
Kurniawan UTY, Faridah, Sunarno.
europepmc   +1 more source