Results 41 to 50 of about 38,128 (219)

Investigation of Mass Transfer Coefficient under Jetting Conditions in a Liquid-Liquid Extraction System [PDF]

Iranian Journal of Chemistry & Chemical Engineering, 2010
In this research mass transfer coefficient under jetting regime in different directions (from dispersed to continuous and continuous to dispersed phase) has been studied using an experimental setup.
Ferial Nosratinia, Mohammad Reza Omidkhah, Dariush Bastani, Ali Akbar Saifkordi   +3 more
doaj  

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Rebound Characteristics of Wet-Shotcrete Particle Flow Jet from Wall Based on CFD-DEM

Buildings
This paper aims to reveal the motion law and collision behaviors of shotcrete particle flow jets. A physical model of the jet flow field composed of a nozzle structure and jet area was constructed and meshes with various sizes were used to mesh the ...
Lianjun Chen, Yang Zhang, Pengcheng Li, Gang Pan   +3 more
doaj   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

ENVIRONMENTALLY SAFE CONTINUOUS CASTING OF HYPEREUTECTIC FINE-CRYSTALLINE SILUMIN INGOTS

Литьë и металлургия, 2010
It is shown that continuous horizontal casting of alloy AK18 into jet crystallizer with application of flooded – jet systems of ingot cooling and hereditary modifying enables to create ecologically safe technological process of production of alloy AK18 ...
V. Ju. Stetsenko, A. M. Pevnev, Suk-Bong Kang   +2 more
doaj   +1 more source

Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy

Advanced Engineering Materials, EarlyView.
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb, Zachary T. Kloenne, Samuel R. Rogers, Chi Hang Dominik Kwok, Mark C. Hardy, Michele S. Conroy, David Dye   +6 more
wiley   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

A continuous calibration of the ATLAS flavour-tagging classifiers via optimal transportation maps

European Physical Journal C: Particles and Fields
A calibration of the ATLAS flavour-tagging algorithms using a new calibration procedure based on optimal transportation maps is presented. Simultaneous, continuous corrections to the b-jet, c-jet, and light-flavour jet classification probabilities from ...
ATLAS Collaboration
doaj   +1 more source

Experimental investigation of a control synthetic jet

EPJ Web of Conferences, 2012
Synthetic jets were used in previous studies to control a continuous round air jet. This study focuses on the single synthetic jet, which is measured using Constant Temperature Anemometry (CTA) and Particle Image Velocimetry (PIV).
Kopecký Václav, Trávníček Zdeněk, Kordík Jozef, Němcová Lucie   +3 more
doaj   +1 more source