Results 11 to 20 of about 3,736,155 (339)
ISIJ International, 2016 The continuous casting of steel (shown in Fig. 1) is a very successful process and the performance of the mould powder is a key factor in this success.
K. Mills
semanticscholar +3 more sources
Three Dimensionally Printed Versus Conventional Casts in Pediatric Wrist Fractures [PDF]
Cureus, 2021 Background and objective With significant advancement in the field of biomaterials, alternatives to conventional fiberglass casts such as customized three-dimensional (3D) orthotics have been developed. However, there is a scarcity of reported experience regarding 3D-printed orthoses.
Skibicki, Hope E +7 more
openaire +2 more sources
Investigation of Tribological and Mechanical Properties of Biodegradable AZ91 Alloy Produced by Cold Chamber High Pressure Casting Method [PDF]
Archives of Metallurgy and Materials, 2020 In this study, AZ91 Magnesium alloy is produced by cold chamber high pressure die casting (HPDC) method. Different combinations of the cold chamber HPDC process parameters were selected as; in-mold pressure values of 1000 bar and 1200 bar, the gate speed
Levent Urtekin +3 more
doaj +1 more source
Influence of Semisolid and Strontium Addition on Dry Sliding Wear Behavior of Hypoeutectic Al-Si Alloy [PDF]
Archives of Metallurgy and Materials, 2023 The study aims to investigate the effect of semisolid structure and strontium (Sr) addition on the wear behavior of hypoeutectic Al-Si alloy. Semisolid hypoeutectic Al-Si alloy was prepared using cooling slope casting with addition of 0 to 0.93 wt.% Sr ...
N.M. Anas +4 more
doaj +1 more source
Functional cast-bracing for Colles' fractures. A comparison between cast-bracing and conventional plaster casts [PDF]
The Journal of Bone and Joint Surgery. British volume, 1984 The use of Orthoplast cast-bracing to allow early hand function in the treatment of displaced Colles' fractures was investigated in 243 patients. They were randomly allocated into three groups: in the first a conventional Colles' type plaster was used; in the second an above-elbow cast-brace with the forearm in supination; and in the third a below ...
H D, Stewart, A R, Innes, F D, Burke
openaire +2 more sources
Metals, 2021 Based on conventional hot rolling processes and strip casting processes, Cu precipitation strengthening is used to improve the strength of non-oriented silicon steel in order to meet the requirements of high-speed driving motors of electric vehicles ...
Feng Fang +9 more
doaj +1 more source
The improvement of aluminium casting process control by application of the new CRIMSON process [PDF]
, 2012 All The traditional foundry usually not only uses batch melting where the aluminium alloys are melted and held in a furnace for long time, but also uses the gravity filling method in both Sand Casting Process (SCP) and Investment Casting Process (ICP).
Dai, Xiaojun J. +2 more
core +1 more source
The Journal of Indian Prosthodontic Society, 2015 Background: Conventional investing and casting techniques are time-consuming and usually requires 2-4 h for completion. Accelerated nonstandard, casting techniques have been reported to achieve similar quality results in significantly less time, namely ...
Deepa Alex +4 more
doaj +1 more source
An a Priori Discussion of the Fill Front Stability in Semisolid Casting
Technologies, 2022 Metal casting is an industrially important manufacturing process offering a superior combination of design flexibility, productivity and cost-effectiveness, but has limitations due to filling related defects.
Anders E. W. Jarfors +2 more
doaj +1 more source
The capability enhancement of aluminium casting process by application of the novel CRIMSON method [PDF]
, 2011 The conventional foundry not only frequently uses batch melting, where the aluminium alloys are melted and held in a furnace for long time, sometimes as long as a complete shift, but also uses the gravity sand casting process where the molten aluminium
Dai, Xiaojun +2 more
core +1 more source