Results 111 to 120 of about 317 (214)

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Projeto de um Conversor CC-CC do tipo Elevador

, 2017
Este trabalho apresenta o estudo e avaliação experimental da topologia e controlo de um conversor CC-CC elevador a operar em modo de condução contínua (CCM) com potência de saída entre os 20W e os 100W, que tem como tensão primária qualquer fonte de energia CC de 24V.
openaire   +1 more source

Conversor CC-CC elevador de tensão para aplicações de energy harvesting

, 2016
Ao longo das últimas décadas os dispositivos portáteis alimentados com baixa tensão têm vindo a aumentar e, consequentemente, algumas fontes de recolha de energia a partir do ambiente envolvente. Para permitir a aplicação dessas fontes de recolha de energia a dispositivos eletrónicos portáteis, verificou-se a necessidade do uso de conversores Corrente ...
openaire   +2 more sources

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Natural Bone‐Derived Ceramic Scaffolds Functionalized with Chitosan‐Gold, Chitosan‐Magnesium, and Chitosan‐Zinc for Enhanced Antibacterial Activity

Advanced Engineering Materials, EarlyView.
This study reports the development of antibacterial ceramic scaffolds derived from natural bovine bone. The bones were processed through sequential boiling and hydrogen peroxide treatment to remove organic matter, producing porous, mineral‐rich scaffolds.
Mohamad Hassan Taherian, Anh Thi Le, Anh Thi Van Le, Dung My Thi Dang, Tin Chanh Duc Doan, Chien Mau Dang, Martin Bolduc   +6 more
wiley   +1 more source

Duas alternativas para conversores CC-CC de alta tensão isolados com elevado rendimento para aplicações aeroespaciais.

Revista Tecnologia, 2009
Neste artigo são propostas duas alternativas para a implementação de conversores CC-CC isolados, operando com elevada tensão de saída(kV) e com tensão de entrada não regulada.
Roger Gules, Ivo Barbi
doaj  

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

Advanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele, Hossein Ipakchi, Tizazu H. Mekonnen   +2 more
wiley   +1 more source