Results 121 to 130 of about 12,663,341 (243)
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Solar Roof Cooling by Evaporation
, 1980 Evaporation is nature's way of cooling. By spraying a light film of water in the form of a mist for thirty seconds, then turning the sprays off for five minutes while evaporation takes place, the roof temperature can be reduced from 1650o to 880o.
Patterson, G. V.
core
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Binder‐free laser powder bed fusion of 8YSZ with a femtosecond laser is used to map process windows linking scan strategy, heat accumulation, and grain growth. Time‐resolved thermography and simulations reveal thermal regimes that enable continuous, vitrified, and fine‐grained 8YSZ surface layers without absorptive additives and demonstrate ...
Markus Kühn +5 more
wiley +1 more source
The performance and application of cross flow fans for automotive engine cooling systems [PDF]
, 1986 The work reported centres on the application of cross flow fan units to provide forced air flow over the radiator used for engine cooling. It is shown that a cooling system in which the airflow is ducted through the vehicle would lead to a significant ...
Fernando, L.M
core
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Research Advances in Free Cooling Technology of Data Centers
Zhileng xuebao, 2016 The increasing energy consumption of data centers attracts more and more attention, much of which is consumed by the cooling system. Utilizing efficient cooling methods is the urgent need for realizing emission control targets, and the free cooling is ...
Zhang Hainan +2 more
doaj
Cooling performance measurements of different types of cooling vests using thermal manikin
Fashion and TextilesThis study compared the effectiveness of five commercially available cooling vests using three distinct thermal manikin test protocols. In addition, the constraints associated with each test protocol were elucidated, facilitating the identification of ...
Siyeon Kim +3 more
doaj +1 more source
Use of Different Cooling Methods in Pig Facilities to Alleviate the Effects of Heat Stress-A Review. [PDF]
Animals (Basel), 2020 Godyń D +3 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source