Results 1 to 10 of about 881,336 (175)
Numerical Investigations on Material Flow During Indirect Extrusion of Copper-Clad Aluminum Rods [PDF]
Frontiers in Materials, 2020 In the extrusion of clad composite materials with different flow stresses are usually used. This causes an inhomogeneous material flow which can induce sleeve or core fracture.
Stefan Kuhnke +4 more
doaj +5 more sources
Influence of Die Surface Topography and Lubrication on the Product Quality during Indirect Extrusion of Copper-Clad Aluminum Rods [PDF]
Metals, 2020 Copper-clad aluminum rods are usually fabricated using hydrostatic extrusion, since during direct and indirect extrusion fracture of the copper sleeve is difficult to avoid.
Stefan Kuhnke +4 more
doaj +4 more sources
Strength and HRTEM microstructure at bond interface of aluminum/copper clad materials
Keikinzoku/Journal of Japan Institute of Light Metals, 2009 It is known that it is difficult to bond dissimilar metals such as aluminum and copper or aluminum and iron using diffusion bonding, because an intermetallic compound is easily produced at the bond interface and bonding strength becomes low. However it is possible to bond the dissimilar metals using the vacuum roll bonding which performs hot rolling in
Tomiko Yamaguchi, Kazumasa Nishio
exaly +5 more sources
Twin Roll Caster for Clad Strip
Metals, 2021 Production of aluminum alloy clad strips requires many processes, and a reduction in the number of processes has long been demanded. A method to cast clad strips directly from molten metal using a twin roll caster with copper rolls is proposed in this ...
Toshio Haga
doaj +2 more sources
AC Resistance of Copper Clad Aluminum Wires
IEICE Transactions on Communications, 2013 Recently, wireless power transfer has attracted much attention for power supplying on not only small electric devices but also large equipments such as electric and hybrid vehicles [1]. Coils are key components in a power transfer system and the AC resistance determines the transferring efficiency.
Ning, Guan +3 more
exaly +3 more sources
Investigation of AL/CU Bimetallic Tube Cladding Process by Severe Plastic Deformation [PDF]
JES: Journal of Engineering Sciences, 2023 In this paper, a new cladding process is proposed and implemented on a bimetallic tube of copper and aluminum. Obtaining a good mechanical bond between the tube’s layers using simple setup components with low required process force and without using ...
Ahlam Ali +3 more
doaj +1 more source
Materials Research Express, 2020 The copper clad aluminum (CCA) wire was fabricated by roll forming of copper foil around the aluminum wire rode. Non-continuous wire drawing (NCWD) was employed to study the effect of wire drawing parameters on ductility, micro-hardness and ...
Fariborz Fatehi Sichani +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 In this study, a Ti/Al/Cu three-layer clad sheet was fabricated using horizontal twin-roll casting (HTRC) technology. The interfacial morphology, interfacial microstructure and phases, interfacial bonding strength, micro-hardness, and tensile properties ...
Jiujian Xu +5 more
doaj +1 more source
Metals, 2023 With the development of laser surface modification techniques like direct laser metal deposition (DLMD), titanium alloy (TI6Al4V) may now have its entire base metal microstructure preserved while having its surface modified to have better characteristics.
Olawale Samuel Fatoba, Tien-Chien Jen
doaj +1 more source
Interfacial Morphology and Bonding Mechanism of Explosive Weld Joints
Chinese Journal of Mechanical Engineering, 2021 Interfacial structure greatly affects the mechanical properties of laminated plates. However, the critical material properties that impact the interfacial morphology, appearance, and associated bonding mechanism of explosive welded plates are still ...
Tingting Zhang +3 more
doaj +1 more source