Results 61 to 70 of about 163,552 (306)
Microstructure and chemical composition of Roman orichalcum coins emitted after the monetary reform of Augustus (23 B.C.) [PDF]
, 2019 A collection of ancient Roman orichalcum coins, i.e., a copper-zinc alloy, minted under the reigns from Caesar to Domitianus, have been characterised using scanning electron microscopy (SEM-EDS) and electron microprobe analysis (EMPA).
Catalli F. +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Nuclear FusionIn future fusion reactors, the first wall will be irradiated with hydrogen fuel (deuterium (D), tritium (T)) and helium (He) with low energies. In this work, the effects of He plasma irradiation on D permeation through tungsten (W) coated reduced ...
Yue Xu +6 more
doaj +1 more source
Comparative Assessment of Magnesium, Copper, and Zinc Addition to Aluminium Waste Casting for Improving Ship Material Behaviour [PDF]
TransNavThe aluminium industry for ship materials produces waste material that can pollute the environment. To protect the environment from material pollution, the aluminium waste recycling process can be used to develop ship material. This study aims to analyze
Kiryanto Kiryanto +6 more
doaj +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Stress corrosion cracking in Al-Zn-Mg-Cu aluminum alloys in saline environments [PDF]
, 2012 Copyright 2013 ASM International. This paper was published in Metallurgical and Materials Transactions A, 44A(3), 1230 - 1253, and is made available as an electronic reprint with the permission of ASM International.
A. Berzin +81 more
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Electroplating on titanium alloy [PDF]
, 1971 Activation process forms adherent electrodeposits of copper, nickel, and chromium on titanium alloy. Good adhesion of electroplated deposits is obtained by using acetic-hydrofluoric acid anodic activation ...
Lowery, J. R.
core +1 more source
Filling Narrow Trenches by Iodine-Catalyzed CVD of Copper and Manganese on Manganese Nitride Barrier/Adhesion Layers [PDF]
, 2011 We present a process for the void-free filling of sub-100 nm trenches with copper or copper-manganese alloy by chemical vapor deposition (CVD). Conformally deposited manganese nitride serves as an underlayer that initially chemisorbs iodine.
Au, Yeung Billy +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source