Results 41 to 50 of about 148,672 (304)
Nickel, copper and cobalt coalescence in copper cliff converter slag [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2016 The aim of this investigation is to assess the effect of various additives on coalescence of nickel, copper and cobalt from slags generated during nickel extraction.
Wolf A., Mitrašinović A.M.
doaj +1 more source
Electrochemical deposition of copper on zinc and its alloys
Журнал Белорусского государственного университета: Химия, 2022 A new electrolyte composition and deposition conditions of quality (light, densely packed, homogeneous) copper coatings on zinc and its alloys were found.
Boris V. Kuznetsov
doaj +1 more source
OBTAINING WEAR-RESISTANT COATINGS ON COPPER ALLOYS UNDER SHS CONDITIONS [PDF]
, 2018 Obtaining wear-resistant coatings on copper alloys under shs ...
KRUGLYAK, D. +3 more
core
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Generalised stacking fault energies of copper alloys - density functional theory calculations [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2019 Generalised stacking fault energies of copper alloys have been calculated using density functional theory. Stacking fault energy of copper alloys is correlated with the d–electrons number of transition metal alloying element.
Muzyk M., Kurzydłowski K.J.
doaj +1 more source
Study of crevice-galvanic corrosion of aluminum [PDF]
, 1967 Corrosion effects of aluminum-copper and aluminum-nickel couples in oxygenated distilled water, and aluminum alloys in oxygenated copper sulfate solution were studied. One of each of the couples had a water tight seal, and showed no substantial corrosion,
Draley, J. E., Loess, R. E., Mori, S.
core +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Metals, 2022 In this paper, the research progress on the strengthening of copper and copper alloy is reviewed. The research shows that traditional strengthening methods are often accompanied by the decrease of plasticity, and there are limitations in size, cost, and ...
Zongxuan Li +8 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source