Results 121 to 130 of about 619,710 (248)
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection
Advanced Engineering Materials, EarlyView.A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
IRN2Vec: A representation learning model for road network intersections by integrating geospatial attributes and travel behaviors. [PDF]
PLoS OneYang X.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Beyond writing machines: A Kano model analysis of researchers' hierarchical needs for AIGC services across the research lifecycle. [PDF]
PLoS OneKong Y, Dong T, Chen R, Wu Y, Yang Z.
europepmc +1 more source