Results 21 to 30 of about 39,762 (260)
Molecules, 2016 Conventional techniques for identifying antioxidant and phenolic compounds in native Australian food plants are laborious and time-consuming. Here, we present a multiplexed detection technique that reduces analysis time without compromising separation ...
Emmanuel Janaka Rochana Rupesinghe +3 more
doaj +1 more source
Comparative Study of the Performance Improvement of an Axial Compressor with a Micro-Vortex Generator and a Suction Slot [PDF]
Journal of Applied Fluid Mechanics, 2023 Flow control methods have been gradually applied to improve the flow field characteristics of axial compressors. However, most of the current research is focused on the cascade, and few studies have taken a compressor as the research object. Therefore, a
S. Ma, X. L. Sun, W. Cheng, W. L. Chu
doaj +1 more source
Energies, 2022 Both the compressor performance and the 3D flows inside the stator passage are significantly impacted by the stator hub gap. The interplay between leakage flow and corner separation within a cantilevered stator of a highly loaded, low-speed axial ...
Guangfeng An +5 more
doaj +1 more source
Separation Control for a Transonic Convex Corner Flow Using Ramp-Type Vortex Generators
International Journal of Aerospace Engineering, 2022 A flap can be used to control wing camber and as a high-lift device. A convex corner is a simplified model of the upper surface of a flap. At transonic speeds, shock-induced boundary layer separation (SIBLS) occurs at greater freestream Mach numbers and ...
Kao-Chun Su +2 more
doaj +1 more source
The Effect of Trailing Edge Clearance in Suppressing Hub-Corner Stall
Energies, 2019 Hub corner is a high-loss area located within in the blade passages of turbomachinery. It is well known that flow separation and vortex development in this area directly affects, not only energy loss and efficiency, but also the stability of axial ...
Wenfeng Zhao +3 more
doaj +1 more source
Cantilevered Tandem Stator in Annular High Speed Test Rig
International Journal of Turbomachinery, Propulsion and Power, 2022 The present paper investigates the aerodynamic performance of a cantilevered tandem stator based on experiments conducted within a high speed annular test rig at the Technische Universitaet Berlin.
Roland Rückert, Dieter Peitsch
doaj +1 more source
A steady separated viscous corner flow [PDF]
Journal of Fluid Mechanics, 1991 An example is presented of a separated flow in an unbounded domain in which, as the Reynolds number becomes large, the separated region remains of size 0(1) and tends to a non-trivial Prandtl-Batchelor flow. The multigrid method is used to obtain rapid convergence to the solution of the discretized Navier-Stokes equations at Reynolds numbers of up to ...
openaire +3 more sources
The Investigation of a New End Wall Contouring Method for Axial Compressors
Applied Sciences, 2022 To further control corner separation in high-load axial compressors, this study proposes a new end wall contouring method. It defines multiple standard “surface units” with particular flow control effects and then applies a linear combination, finally ...
Xiangjun Li +4 more
doaj +1 more source
Influence of a Wavy Blade-End Applied in an Axial Compressor Cascade on the Secondary Flow of the Passage [PDF]
Journal of Applied Fluid Mechanics, 2022 To improve the compressor performances at variable conditions, in this research, we used numerical simulation software to analyze and discuss the effects of three kinks of a wavy blade-end on an axial compressor cascade.
S. Ma, F. Li, L. Gui, D. Chen, T. Duan
doaj +1 more source
Seal leakage Flow-affected Compressor Endwall and Fillet Profiling Design: Based on Optimization and Data Mining [PDF]
Journal of Applied Fluid MechanicsIn current research of axial compressor, flow control profiling designs for corner separation often overlook the influence of seal leakage flows, whose impact grows with increasing single-stage pressure ratios. Seal leakage flow alters near-wall velocity
Y. Shen, W. Chu, J. Chen
doaj +1 more source