Results 71 to 80 of about 716,966 (306)
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Tannic acid compound as a corrosion inhibitor: film-forming characteristics and corrosion resistance
工程科学学报, 2019 Tannic acid (TA) is widely used to protect metals from corrosion because it is environmentally friendly and inexpensive. However, the single effect of TA used as corrosion inhibitor has been widely investigated and studies focusing on the corrosion ...
Tao FANG +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source
Journal of Materials Research and TechnologyAlCoCrFeNi2.1 eutectic high-entropy alloys (EHEAs) show great potential in high-temperature applications due to the dual-phase lamellar structure. In this work, the high-temperature oxidation behavior and scaling mechanisms of three AlCoCrFeNi2.1 EHEAs ...
Qinying Huang +8 more
doaj +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Corrosion assessment on reinforced concrete and its service life prediction [PDF]
, 2005 Deterioration of structural concrete may be caused either by chemical or physical effects. Corrosion of embedded steel is a major cause of deterioration of concrete structures at the present time.
Syed Mohamad, Syed Burhanuddin Hilmi
core
Intergranular Corrosion of 2024 Alloy in Chloride Solutions [PDF]
, 2007 Experiments were performed to determine the propagation kinetics of intergranular corrosion on 2024 aluminum alloy immersed in 1 and 3 M chloride solutions.
Andrieu, Eric +4 more
core +4 more sources
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Effect of salt spray environment on the corrosion behavior of PCB-HASL and PCB-ENIG
工程科学学报, 2015 The corrosion behavior of hot air solder level printed circuit boards(PCB-HASL) and electroless nickel immersion gold printed circuit boards(PCB-ENIG) in salt spray test was studied by electrochemical impedance spectroscopy.
YI Pan +6 more
doaj +1 more source