Results 91 to 100 of about 243,201 (307)
Corrosion CommunicationsCorrosion behavior of 7050-T7451 aluminum (Al) alloy in a salt spray environment was investigated, with a particular focus on the relationship between grain configurations and corrosion behavior, highlighting the mechanisms of exfoliation corrosion ...
Yuan Li +4 more
doaj +1 more source
Influence of Laser Processing Parameters on the Corrosion Behavior in 316L Stainless Steel Laser Powder Depositions [PDF]
, 2004 Mechanical ...
Anderson, Alan J. +2 more
core +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Corrosion behavior of duplex coatings
Journal of King Saud University - Engineering Sciences, 2016 The titanium alloys are used in defense, aerospace, automobile, chemical plants and biomedical applications due to their very high strength and lightweight properties. However, corrosion is a life-limiting factor when Ti alloys are exposed to different chemical environments at high temperatures.
K. Raghu Ram Mohan Reddy +2 more
openaire +2 more sources
Electrochemical study of aluminum corrosion in boiling high purity water [PDF]
, 1969 Electrochemical study of aluminum corrosion in boiling high-purity water includes an equation relating current and electrochemical potential derived on the basis of a physical model of the corrosion process.
Draley, J. E., Legault, R. A.
core +1 more source
Investigation on some factors affecting crack formation in high resistance aluminum alloys [PDF]
, 2017 Aluminum alloys having good mechanical properties are Al-Zn-Mg alloys (7xxx) and Al-Cu-Li alloys (Weldalite®). These alloys may be subjected to stress corrosion cracking.
Brotzu, A., Felli, F., Pilone, D.
core +3 more sources
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Corrosion and corrosion prevention in gas turbines [PDF]
The conditions governing the corrosion behavior in gas turbines are surveyed. Factors such as temperature, relative humidity, the presence of sulfur and nitrogen dioxide, and fuel quality are discussed.
Kolkman, H. J., Mom, A. J. A.
core +1 more source
Tribocorrosion Properties of PEO Coatings Produced on AZ91 Magnesium Alloy with Silicate- or Phosphate-Based Electrolytes [PDF]
, 2018 In this work, the tribocorrosion behavior of plasma electrolytic oxidation (PEO)-coated AZ91 samples was studied. In particular, two different coatings were produced and compared. One was obtained with an alkaline electrolyte containing sodium phosphate,
Brunelli, Katya +7 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source