Results 141 to 150 of about 752,940 (273)

Experimental Comparative Analysis of Hole‐Making Strategies and Cutting Parameters on Flexural Properties and Induced Delamination in S2 Glass and Basalt Fiber‐Reinforced Polymers

Polymer Composites, EarlyView.
Hole‐making strategy and machining parameters influence delamination and hole quality in S2‐glass and basalt FRP composites, which subsequently affet flexural performance. Improved hole integrity leads to enhanced structural performance during three‐point bending.
Sara Saeed Abdulrahman Eltahir, Cagatay Yilmaz, Sinan Kesriklioglu   +2 more
wiley   +1 more source

Application of 3D scanning technology in Royal Malaysian Air Force Industrial Revolution 4.0‐based aircraft maintenance

IET Networks, EarlyView., 2022
Abstract 3D scanning is rapidly becoming a key maintenance tool. Aerospace was a pioneer in adopting 3D scanning technology because aircraft manufacture and maintenance require precision. Monitoring deterioration, removing components for maintenance, and verifying covert operations are not practical or helpful without technology.
T. Nanthakumaran Thulasy, Puteri N. E. Nohuddin, Istas Fahrurrazi Nusyirwan, Mohd Hanafi Ahmad Hijazi, Musaddak Maher Abdul Zahra   +4 more
wiley   +1 more source

Corrosion, Fatigue and Corrosion Protection of Metals and Their Alloys in Various Environments. [PDF]

Materials (Basel)
Branzoi F.
europepmc   +1 more source

Second‐Life Thermoset Manufacturing via Mild Solvolysis of Epoxy‐Matrix Composites and Wet‐Laid Mat Production

Polymer Composites, EarlyView.
From end‐of‐life pultruded CFRP profiles (1) to second life composites (7) through mild solvolysis (2,3), wet‐laid nonwoven mat fabrication (4), resin impregnation (5), and compression molding (6). ABSTRACT The growing use of carbon fiber–reinforced thermosets has led to the accumulation of significant composite waste, posing environmental and economic
Ehsan Zolfaghari, Fabian Rechsteiner, Violetta Schumm, Emanuela Muscolino, Sabina Alessi, Nadka Tz. Dintcheva, Clelia Dispenza   +6 more
wiley   +1 more source

Corrosion Fatigue

CORROSION ENGINEERING, 1977
openaire   +4 more sources

Corrosion Fatigue of a Nickel-Based Superalloy Disc Rotor with Salt in Air and Sulphur Dioxide Environments. [PDF]

Materials (Basel)
Li Y, Davies H, Hardy M, Jackson C, Whittaker M.   +4 more
europepmc   +1 more source

Nano‐Engineered Basalt Fiber Composites With Halloysite Nanotubes: Durability and Drilling Behavior After Acidic Aging

Polymer Composites, EarlyView.
Schematic summary of the drilling damage and microstructural degradation mechanisms in basalt fiber‐reinforced composites after acidic aging. ABSTRACT This study investigates the drilling performance and environmental durability of basalt fiber reinforced polymer (BRC) and halloysite nanotube (HNT) modified basalt nanocomposites (BRnC) exposed to ...
İbrahim Aslan, Harun Yaka, Hasan Ulus, Halil Burak Kaybal   +3 more
wiley   +1 more source

Corrosion fatigue life prediction of multiple austenitic stainless steel grades in high-temperature, high-pressure water environments using a GA-optimized neural network. [PDF]

Sci Rep
Bhardwaj HK, Shukla M.
europepmc   +1 more source

Effect of Veil Interlayer Type and Placement on the Mechanical Response of Carbon and Glass Fiber/Epoxy Composites

Polymer Composites, EarlyView.
Veil interlayers of five different chemistries (PI, FG, PPS, PEI, PEEK) were placed at two through‐thickness positions in carbon and glass fiber/epoxy laminates and evaluated under interlaminar shear (ILSS), three‐point bending (3PB) and axial buckling loading. The optimum placement was found to be loading mode dependent: near‐surface placement favored
Yavuz Selim Tarih, Burak Hülagü, Ömer Gündoğdu, Adem Yar   +3 more
wiley   +1 more source

Effects of Pre-Deformation in Corrosion Fatigue Crack Growth of Al-Mg-Zn Alloy. [PDF]

Materials (Basel)
Jiang H, Jin J, Fang Y, Gou G, Lu W, Zhang Z, Zhou H, Sun H, Feng J, Chen J, Fu Z.   +10 more
europepmc   +1 more source