Results 171 to 180 of about 22,195 (309)

Embedding Fiber Segment Interferometry for Localization of Defects in Composite Structures

Polymer Composites, EarlyView.
Graphical representation of composite structures with embedded fiber optic sensors for structural health monitoring, enabling strain measurement and damage localization under mechanical loading. ABSTRACT In the area of structural health monitoring (SHM), embedding strain sensors into smart composites is a key strategy for detecting failures arising ...
Shiva Mohammadkarimi, Christoph Hemeling, Thomas Kissinger, Florian Puch   +3 more
wiley   +1 more source

Corrosion Fatigue of a Nickel-Based Superalloy Disc Rotor with Salt in Air and Sulphur Dioxide Environments. [PDF]

Materials (Basel)
Li Y, Davies H, Hardy M, Jackson C, Whittaker M.   +4 more
europepmc   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, EarlyView.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

Corrosion fatigue life prediction of multiple austenitic stainless steel grades in high-temperature, high-pressure water environments using a GA-optimized neural network. [PDF]

Sci Rep
Bhardwaj HK, Shukla M.
europepmc   +1 more source

Mode I and Mode II Interlaminar Fracture Toughness of Basalt/Kevlar Fiber Reinforced Epoxy Resin Hybrid Composites Incorporating Graphene Nanoplatelets

Polymer Composites, EarlyView.
Processing the Mode I and Mode II fracture analysis Basalt/Kevlar fiber reinforced hybrid composites with GnP. ABSTRACT This research examines the Mode I and Mode II fracture behavior of basalt/Kevlar fiber reinforced epoxy hybrid composites augmented with graphene nanoplatelets (GnP). Hybrid composites containing varying concentrations of GnP (0, 1, 2
Mehmet Bulut, Ömer Yavuz Bozkurt, Atban R. Abdo, Ahmet Erkliğ   +3 more
wiley   +1 more source

Effects of Pre-Deformation in Corrosion Fatigue Crack Growth of Al-Mg-Zn Alloy. [PDF]

Materials (Basel)
Jiang H, Jin J, Fang Y, Gou G, Lu W, Zhang Z, Zhou H, Sun H, Feng J, Chen J, Fu Z.   +10 more
europepmc   +1 more source

Experimental Comparative Analysis of Hole‐Making Strategies and Cutting Parameters on Flexural Properties and Induced Delamination in S2 Glass and Basalt Fiber‐Reinforced Polymers

Polymer Composites, EarlyView.
Hole‐making strategy and machining parameters influence delamination and hole quality in S2‐glass and basalt FRP composites, which subsequently affet flexural performance. Improved hole integrity leads to enhanced structural performance during three‐point bending.
Sara Saeed Abdulrahman Eltahir, Cagatay Yilmaz, Sinan Kesriklioglu   +2 more
wiley   +1 more source

Corrosion Fatigue

Journal of the Society of Materials Science, Japan, 1978
openaire   +2 more sources

Enhanced Experimental Setup and Methodology for the Investigation of Corrosion Fatigue in Metallic Biodegradable Implant Materials. [PDF]

Materials (Basel)
Schumacher L, Cetin IN, Bielefeldt S, Rupp F, Roehler A.   +4 more
europepmc   +1 more source

Fusion Bonding Repair of Impact‐Damaged Elium Laminates: Comparison of Hot Pressing and Joule Heating

Polymer Composites, EarlyView.
Joule Heating‐Enabled Repair of Impact‐Damaged GFRP/Elium Laminates. ABSTRACT This study investigates the repairability of glass fiber‐reinforced Elium (GFRP/Elium) laminates incorporating nickel‐coated carbon veils, focusing on hot pressing and Joule heating as fusion bonding repair techniques.
Ozan Can Zehni
wiley   +1 more source