Results 21 to 30 of about 347,437 (244)

Tribocorrosion behaviour of NiTiNOL60 alloy in an alkaline environment

Results in Engineering, 2023
NiTi-based alloys subjected to aggressive tribocorrosion working conditions can deteriorate by the combined action of mechanical and chemical wear.
Anthony Okoani, Ashveen Nand, Maziar Ramezani   +2 more
doaj   +1 more source

Wear Behavior of Commercial Tire Rubber against Mild Steel in Dry, Wet and 3.5% NaCl Corrosive Environment

JEMMME (Journal of Energy, Mechanical, Material, and Manufacturing Engineering), 2020
The tribological performance of commercially used tire rubber was evaluated at ambient conditions under dry, wet and 3.5% NaCl corrosive environment. A pin-on-disc apparatus was used for the experiment.
Samiul Kaiser, Mohammad Salim Kaiser, Sheikh Reaz Ahmed   +2 more
doaj   +1 more source

An Experimental Study on the Fretting Corrosion Behaviours of Three Material Pairs at Modular Interfaces for Hip Joint Implants

Lubricants, 2021
The fretting corrosion behaviours of Al2O3 ceramic/Ti6Al4V alloy, 316 L stainless/Ti6Al4V alloy, and CoCrMo alloy/Ti6Al4V alloy pairs were studied in an in-house developed fretting-corrosion tester.
Jian Pu, Dongsheng Wu, Yali Zhang, Xiaogang Zhang, Zhongmin Jin   +4 more
doaj   +1 more source

Erosion-corrosion and wear [PDF]

Le Journal de Physique IV, 1993
The basic processes of wear, erosion and erosion-corrosion are reviewed. It is shown that oxide debris can accelerate wear when it is present as particulates, or protect and reduce friction when it is present as a glaze. Erosion-corrosion processes can be understood and organized in a series of regimes that represent a sequence of change in the ...
Birks, N., Pettit, F., Rishel, D.
openaire   +1 more source

Wear Properties Analysis on Al-Based Automotive Alloy with Varied Levels of Si in Dry, 3.5% NaCl and Seawater Corrosive Environments [PDF]

Archives of Metallurgy and Materials
The wear tests of aluminum based automotive alloys with different Si content in 3.5% NaCl, seawater and dry sliding environment are carried out. A conventional pin-on-disc wear apparatus is used at 2.55 MPa pressure and 0.51 m/s speed for a sliding ...
A.A. Khan, M.S. Kaiser
doaj   +1 more source

Mitigation of tribocorrosion of metals in aqueous solutions by potential-enhanced adsorption of surfactants

Friction, 2023
Corrosion and corrosive wear occur commonly on metals surface in aqueous solutions. External electric field is usually considered as one of the factors to accelerate corrosion or corrosive wear of materials in the presence of conventional electrolytes ...
Chenxu Liu, Yu Tian, Zulfiqar A. Khan, Yonggang Meng   +3 more
doaj   +1 more source

Experimental study of corrosion wear of structures in a plane stress state and identification of corrosion wear models [PDF]

E3S Web of Conferences
The problem of experimental study of the influence of the stress state on the kinetics of corrosive wear of thin-walled metal structures is considered.
Karakhanyan Vadim, Mavzovin Vladimir, Ovchinnikov Ilya   +2 more
doaj   +1 more source

Corrosive and abrasive wear in ore grinding [PDF]

, 1985
The relative significance of corrosive and abrasive wear in ore grinding is discussed. Laboratory marked ball wear tests were carried out with magnetic taconite and quartzite under different conditions, namely dry, wet and in the presence of an organic ...
Riemera, S. C., Iwasaki, I., Natarajan, K. A., Orlich, J. N.   +3 more
core   +2 more sources

Comparison of wear performance of low temperature nitrided and carburized 316L stainless steel under dry sliding and corrosive-wear conditions [PDF]

, 2022
The file attached to this record is the author's final peer reviewed version. The Publisher's final version can be found by following the DOI link.316L austenitic stainless steel was plasma nitrided and carburized at low temperatures to produce ...
Sun, Yong, Y. Sun, R. Bailey, Bailey, Richard   +3 more
core   +1 more source

Sliding wear of a-C:H coatings against alumina in corrosive media [PDF]

, 2013
This paper reports the results obtained from the study of friction and sliding wear in two corrosive solutions of an a-C:H coating deposited on 316L stainless against an alumina ball, employed as static counter part. Calculations of the values of the von
La Barbera Sosa, J.G., PUCHI-CABRERA, Eli-Saul, IOST, Alain, Santana Mendez, Y.Y., PUCHI-CABRERA, E.S., CHICOT, Didier, CHICOT, D., van Gorp, A., SANTANA, Y.Y., VAN GORP, Adrien, Carrasquero, E.J., Iost, A., STAIA, M.H., Puchi-Cabrera, Eli Saúl, CARRASQUERO, E., LA BARBERA-SOSA, J.G., Santana-Mendez, Y.Y., Puchi-Cabrera, Eli S., Staia, Mariana H., La Barbera Sosa, José G., Santana, Yucelys Y., Carrasquero, Edwuin   +21 more
core   +1 more source