Results 111 to 120 of about 334,106 (287)
Nature of corrosive and abrasive wear in ball mill grinding
Laboratory results of marked-ball wear tests are used to discuss the relative significance of corrosive and abrasive wear in wet grinding. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion current ...
Pozzo, R. L. +9 more
core +1 more source
Investigation of tribo-corrosion behaviors of SLM-printed CX stainless steel under different loads
CX stainless steel, produced through selective laser melting technology, exhibits a predominance of martensite with minor austenite. The fine-grained structure of CX stainless steel promote corrosion resistance, while a high density of dislocations and ...
Xiaojie Zhao +4 more
doaj +1 more source
Review of Gastrointestinal Capsule Robots: Materials, Actuation, Diagnostics, and Therapeutics
This review examines gastrointestinal capsule robots through a systems engineering lens, covering shell materials, actuation and localization strategies, diagnostic modalities, therapeutic interventions, and commercialization status. By mapping the complete technological chain from fabrication to clinical deployment, this work identifies critical gaps ...
Zengsheng Li +8 more
wiley +1 more source
The corrosion inhibition behavior of imidazoline and porphyrin in hot pressing impregnated diamond bit matrix material in NaCl solution with pH10 and mass fraction of 20% was studied by electrochemical method, weight loss test and Raman spectroscopy. The
YAO Yuanji, PAN Bingsuo, LIU Zhijiang
doaj
Bistable Networks Enable Complex Shape Changes
Transition‐controlled metamaterials are networks of bistable mechanical memory that store local binary states and express them as global shape change. By decoupling low‐force programming from high‐force holding, a single lattice is reconfigured into distinct 2D profiles and 3D surfaces without continuous actuation, enabling reusable morphing materials ...
Sawyer Thomas, Jeffrey Lipton
wiley +1 more source
The Effect of Oil-Water Ratio of Drilling Fluid on the Tribological Properties of 2Cr13 Casing
There are few studies on the influence of drilling fluid lubrication performance on the wear behavior of tubing and casing. In view of this, G105 steel and 2Cr13 steel are used as friction pairs to study the effect of oil-water ratio of drilling fluid on
吕晓平 +4 more
doaj
Bio‐Inspired Gradient Coatings Enhance the Leading Edge Erosion Resistance of Wind Blades
Rain‐induced erosion of the wind turbine blade leading edge poses a critical challenge to maintenance and operation. Here, we propose a bio‐inspired approach for erosion protection utilising a platelet‐reinforced polyurethane coating with a graded through‐thickness architecture.
Natalia Sofia Guevara‐Sotelo +2 more
wiley +1 more source
A high‐power hybrid nanogenerator (HP‐HNG) with multi‐degree‐of‐freedom mechanical coupling is reported, integrating multi‐directional wave energy for output to achieve 1 + 1 > 2 energy harvesting. The HP‐HNG achieves a peak output power of 0.764 W, corresponding to a peak power density of 127.303 W m−3. At a wave frequency of 1 Hz, the HP‐HNG delivers
Shuai Ding +9 more
wiley +1 more source
Cavitation-erosion resistance of eutectic coatings in sodium chloride solution
The paper presents original research results related to the resistance of proprietary eutectic coatings applied to C45 structural steel to cavitation-erosion wear. This type of wear is encountered in devices operating in the chemical, petrochemical, heat
M. Pashechko +3 more
doaj +1 more source
The phosphite group endows intrinsic flame retardancy, while the P = O bond enhances intermolecular interactions to realize solid‐solid phase transition. Battery thermal management tests show the materials extend the safe working time of lithium‐ion batteries by 200%. Cone calorimeter tests indicate a 14s delay in ignition time, and reductions of 37.6%,
Changhui Liu +9 more
wiley +1 more source

