Results 171 to 180 of about 325,141 (264)

An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials

Advanced Engineering Materials, EarlyView.
An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut, Pierre Le Berre, Hamdi Jaballah, Lukas Fink, Victor Poline, Richard Haettel, Stéphane Grenier, Gilbert Chahine, Ewen Bellec, Guillaume Buatier, Wilfried Hortschitz, Santa Pile, Thomas Schrefl, Nils Blanc, Yuan Hong, Thibaut Devillers, Nora M. Dempsey   +16 more
wiley   +1 more source

Low Cycle Repetitive Loading of Ti‐6Al‐4V‐Epoxy Composite Lattice Structures for Enhanced Energy Dissipation and Damage Tolerance

Advanced Engineering Materials, EarlyView.
Composite Ti–6Al–4V–epoxy lattice structures are additively manufactured and epoxy infiltrated for cyclic loading. At low lattice volume fractions, hybridization produces synergistic gains in stiffness and energy dissipation. At higher volume fractions, synergy diminishes, although composites still exceed metallic lattices in specific energy ...
Joey Tallon, Jordan Noronha, Justin Dirrenberger, Andrey Molotnikov   +3 more
wiley   +1 more source

Photo-thermal activation of persulfate for the efficient degradation of synthetic and real industrial wastewaters: System optimization and cost estimation. [PDF]

Environ Sci Pollut Res Int
El-Monem HA, Mahanna H, El-Halwany M, Samy M.   +3 more
europepmc   +1 more source

Enhancing Bubble Removal in Geometry‐Optimized Electrodes

Advanced Engineering Materials, EarlyView.
3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner, Peter Förster, Alexander Limper, Anselm Brodersen, Matthias Wessling, John Linkhorst   +5 more
wiley   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Evaluation and cost estimation of laboratory test overuse in 43 commonly ordered parameters through a Computerized Clinical Decision Support System (CCDSS) in a large university hospital. [PDF]

PLoS One, 2020
Tamburrano A, Vallone D, Carrozza C, Urbani A, Sanguinetti M, Nicolotti N, Cambieri A, Laurenti P.   +7 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

COVID-19 Crisis Management and Cost Estimation Models: Bureaucratic Government Coaction Vs. Spontaneous Social Coordination

, 2021
Huerta de Soto J, Bagus P, Sánchez-Bayón A.   +2 more
europepmc   +1 more source

Cost estimation for the implementation of the Mental Healthcare Act 2017. [PDF]

Indian J Psychiatry, 2019
Math SB, Gowda GS, Basavaraju V, Manjunatha N, Kumar CN, Enara A, Gowda M, Thirthalli J.   +7 more
europepmc   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source