Results 121 to 130 of about 3,405,613 (273)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Elementos Traza en Suelos del Valle de La Paz (B.C.S., México), ¿Están Contaminados?
Terra LatinoamericanaIrrigación con fines agrícolas representa el 60-90% del agua total utilizada para actividades humanas, lo que convierte esta actividad en la mayor consumidora de agua dulce del planeta.
Tatiana A. Acosta-Pachón +2 more
doaj +1 more source
A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions
Advanced Engineering Materials, EarlyView.This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
CR-LDP como protocolo de señalización en redes de conmutación de etiquetas multiprotocolo
Revista Facultad de Ingeniería Universidad de Antioquia, 2011 En este artículo se reportan los eventos suscitados y resultados obtenidos al utilizar CR-LDP como posible protocolo de señalización en redes MPLS, con miras a la búsqueda de la tan anhelada garantía de QoS para aplicaciones deboradoras de ancho de banda.
Danilo López +2 more
doaj
Studying Phase Equilibria in Cr-Si, Cr-C, Cr-AI, Cr-P, Cr-S Metal Systems
Trudy Universiteta, 2021 Nurzhan NURGALI +5 more
openaire +1 more source
Advanced Engineering Materials, EarlyView.Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller +6 more
wiley +1 more source