Results 51 to 60 of about 5,775 (200)

ANSYS Creep-Fatigue Assessment tool for EUROFER97 components

Nuclear Materials and Energy, 2016
The damage caused by creep-fatigue is an important factor for materials at high temperatures. For in-vessel components of fusion reactors the material EUROFER97 is a candidate for structural application where it is subjected to irradiation and cyclic ...
M. Mahler, F. Özkan, J. Aktaa
doaj   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Effect of Pre-Hoop Expansion Deformation on High-Temperature Mechanical Properties of Zirconium Plate at 400 °C

Metals
The role of pre-hoop expansion deformation on high-temperature mechanical properties of zirconium at 400 °C was investigated. The results showed that with the increase in the pre-strain, the yield strength and ultimate strength increased while the ...
Haidong Qi, Li You, Xiping Song
doaj   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Creep–Fatigue Behavior and Life Prediction of Medium-Si-Mo Ductile Iron

Applied Sciences
Exhaust manifolds accumulate creep and fatigue damage under cyclic thermal loading, leading to localized failure. Understanding a material’s mechanical behavior is crucial for accurate life assessment. This study systematically investigated the low-cycle
Mucheng Liu, Huihua Feng, Peirong Ren
doaj   +1 more source

Creep-fatigue interaction in heat resistant austenitic alloys

MATEC Web of Conferences, 2018
This work includes an investigation of two commercial austenitic steels: UNS S21500 (Esshete 1250) and UNS S31035 (Sandvik SanicroTM 25). The materials were exposed to isothermal strain controlled fatigue with load controlled dwell time at maximum strain.
Wärner Hugo, Calmunger Mattias, Chai Guocai, Moverare Johan   +3 more
doaj   +1 more source

A New 3D Creep-Fatigue-Elasticity Damage Interaction Diagram Based on the Total Tensile Strain Energy Density Model

Metals, 2020
Fatigue damage, creep damage, and their interactions are the critical factors in degrading the integrity of most high-temperature engineering structures. A reliable creep-fatigue damage interaction diagram is a crucial issue for the design and assessment
Qiang Wang, Naiqiang Zhang, Xishu Wang
doaj   +1 more source

Historical Foundation and Practical Guideline for Ferroelectric Switching Kinetic Studies

Advanced Functional Materials, EarlyView.
The P and U pulses in the conventional PUND measurements are not identical because of the interplay between switching current and the measurement circuit components. This circuit effect can lead to a shift in polarization transients and misinterpreted physics in the switching kinetics.
Yi Liang, Pat Kezer, John T. Heron
wiley   +1 more source