Results 151 to 160 of about 3,418,678 (290)

Stereotactic two-needle irreversible electroporation of liver tumors near critical structures: a proof-of-concept study. [PDF]

Eur Radiol Exp
Zhang L, Mayr V, Luerken L, Strotzer Q, Brandenstein M, Kupke L, Ngu A, Stroszczynski C, Einspieler I.   +8 more
europepmc   +1 more source

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Risk of exotic disease introduction and propagation in the Austrian swine trade network. [PDF]

iScience
Puspitarani GA, Schuster H, Colman E, Desvars-Larrive A.   +3 more
europepmc   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Prevalence and location of posterior superior alveolar artery in Lebanese population. A retrospective tomography study. [PDF]

Saudi Dent J
Raoof MAA, Merhi YWA, Hammoud MM, El-Mahallawy Y, Adham M, Arakji H.   +5 more
europepmc   +1 more source

PBF‐LB/M of Ti‐6Al‐4V: High‐Pressure Solution Treatment and Aging for Applications in a Sustainable Aerospace

Advanced Engineering Materials, EarlyView.
Additive manufacturing (AM) allows great geometric freedom for lightweight components. As parts are progressively optimized exploiting potentials in AM leading in smaller material cross sections, high pressure solution treating and aging (STA) treatments show an enormous potential for strongly improving material properties.
Mika León Altmann, Andre Danzig, Freerk Syassen, Rainer Fechte‐Heinen, Anastasiya Toenjes   +4 more
wiley   +1 more source

Percolation with Distance-Dependent Site Occupational Probabilities. [PDF]

Entropy (Basel)
Lambrou E, Argyrakis P.
europepmc   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

Cooperative spatial modelling of hospital compliance with minimum caseload requirements. [PDF]

Int J Health Geogr
Ji L, Geraedts M, de Cruppé W.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source