Results 171 to 180 of about 67,496 (315)

Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines

Advanced Engineering Materials, EarlyView.
Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl, Daniel Emil Mack, Martin Tandler, Susanne Schrüfer, Robert Vaßen   +4 more
wiley   +1 more source

Critical Heat Flux in Vertical Two Phase Concentric Tube Thermosyphon. Enhancement of Critical Heat Flux.

TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series B, 1998
MONDE, Masanori, MITSUTAKE, Yuichi, KUSUMOTO, Satoshi   +2 more
openaire   +2 more sources

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

Advanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares, Nadège Bouchonneau, Christian Jochum, Donald Radford   +3 more
wiley   +1 more source

On-chip micro-evaporation: Experimental evaluation of liquid pumping and vapor compression cooling systems

, 2011
This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece.
Marcinichen, JB, Thome, JR, 3rd Micro and Nano Flows Conference (MNF2011)   +2 more
core  

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Multiphysics Investigation on Thermal Characteristics of Internal Bio-Inspired V-Ribbed Cooling Channels for Outer Rotor PMSM. [PDF]

Biomimetics (Basel)
Xiong X, Li X, You S, Zhu B, Ding P, Gao H, Hou Z.   +6 more
europepmc   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Prediction and Mitigation of H₂S-Induced High-Temperature Corrosion in a 660 MW Boiler Water-Wall. [PDF]

Materials (Basel)
Liu J, Gu Y, Feng L, Yang D.
europepmc   +1 more source

Critical Heat Flux in Bottom Heated Two-Phase Thermosyphon. Improvement in Critical Heat Flux Due to Concentric Tube.

TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series B, 2000
MONDE, Masanori, MITSUTAKE, Yuichi
openaire   +2 more sources