Results 161 to 170 of about 1,732,571 (284)

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Coexistence of critical phenomena: the concept of manifold multi-spectral criticality. [PDF]

Sci Rep
Chorowski M, Kutner R, Struzik ZR.
europepmc   +1 more source

Scale-free dynamics and critical phenomena in cortical activity. [PDF]

Front Physiol, 2013
Boonstra TW, He BJ, Daffertshofer A.
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Natural time analysis of critical phenomena. [PDF]

Proc Natl Acad Sci U S A, 2011
Varotsos P, Sarlis NV, Skordas ES, Uyeda S, Kamogawa M.   +4 more
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Critical phenomena and estimation of the spontaneous magnetization from a mean field analysis of the magnetic entropy change in La_0.7Ca_0.1Pb_0.2Mn_0.95Al_0.025Sn_0.025O₃. [PDF]

RSC Adv, 2018
Dhahri K, Dhahri N, Dhahri J, Taibi K, Hlil EK.   +4 more
europepmc   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source